background image

13.  Transporting and storage  

 

Always store the devices in a dry, ventilated place, out of reach of children and 
bystanders. Protect the device against vibrations and shocks during transport. 

 

14.  Recycling 

 
The packaging and device materials are suitable for recycling use. Disposal of the packaging and 
device  must  be  done  in  accordance  with  local  regulations.  The  packaging  materials  should  be 
protected against children as they are potential source of danger. 
 

15.  Warranty 

 

The manufacturer of the device provides full warranty service for the power supply unit within 24 
months from the day device was purchased. An individual warranty card is issued for each device.  
Warranty is valid only if all conditions listed in the instructions manual were fulfilled. If the device 
was used inappropriate or against instructions the warranty becomes invalid. Service centre does 
not cover the postage cost for sending the device for repairs or sending it back after repairs.  
 
BADEK 
ul. Kobierzycka 20D 
52-315 

Wrocław 

Poland 
 
e-mail

[email protected]

 

www: www.badek.pl 

 

Summary of Contents for PRAKTIK MIG 200 IGBT MMA











Reviews: