background image

 

16

 

Installation and Servicing

SECTION 1 - GENERAL

The boiler does not normally need a bypass but at 

least some radiators on the heating circuit, of load 

of at least 10% of the minimum boiler output, must 

be provided with twin lockshield valves so that this 

minimum heating load is always available. See note 

regarding thermostatic radiator valves on section 1.13.

Note. 

Systems incorporating zone valves which could 

completely cut off the flow through the system must 

also include a bypass.

BALANCING

1.

  Set the programmer to ON.

  Close the manual or thermostatic valves on all 

radiators, leaving the twin lockshield valves (on the 

radiators referred to above) in the OPEN position.  

  Turn up the room thermostat and adjust the 

lockshield valve to give an uninterrupted flow 

through the radiator.

  These valves should now be left as set.

2. 

Open all manual or thermostatic radiator valves 

and adjust the lockshield valves on the remaining 

radiators, to give around 20

o

C temperature drop at 

each radiator.

3.

  Adjust  the room thermostat and programmer to 

NORMAL settings. 

1.18 SYSTEM BALANCING

1.19 WATER TREATMENT

CENTRAL HEATING

The Logic Code Combi ESP1 range of boilers have an 

ALUMINIUM alloy heat exchanger.

IMPORTANT.

The application of any other treatment to this 

product may render the guarantee of Ideal Boilers 

Invalid.
Ideal Boilers 

recommend Water Treatment in 

accordance with the Benchmark Guidance Notes on 

Water Treatment in Central Heating Systems.
If water treatment is used 

Ideal Boilers 

recommend 

only the use of 

SCALEMASTER GOLD 100, FERNOX,  

MBI, ADEY MC1 or SENTINEL X100 

inhibitors and 

associated water treatment products, which must 

be used in accordance with the manufacturers’ 

instructions. 

DOMESTIC HOT WATER

In hard water areas where mains water can exceed 

200ppm Total Hardness (as defined by BS 7593:2006 

Table 2) a scale reducing device should be fitted into 

the boiler cold supply within the requirements of the 

local water company. The use of artificially softened 

water, however, is not permitted. 

Ideal Boilers

 recommend the use of Fernox 

Quantomat, Sentinel Combiguard,Calmag CalPhos 

I scale reducing devices or Scalemaster In-line 

Scale Inhibitor branded Ideal, which must be used in 

accordance with the manufacturers’ instructions.

SYSTEM REQUIREMENTS - CONT’D 

 Domestic Hot Water

1.

  The DHW service must be in accordance with BS5546 & BS6700.

2.

  Refer to Table 1 for minimum and maximum working pressures.  

In areas of low mains water pressures the domestic hot water 

regulator may be removed from the DHW flow turbine cartridge.  

Refer to Section 3.25.  The boiler will require the flow rate to be 

set to obtain a temperature rise of 35

o

C at the tap furthest from the 

boiler.

3.

  The boilers are suitable for connection to most types of washing 

machine and dishwasher appliances.

4.

  When connecting to suitable showers, ensure that:

a.

 The cold inlet to the boiler is fitted with an approved anti-

     vacuum or syphon non-return valve.

 

b.

 Hot and cold water supplies to the shower are of equal pressure.

5.  Hard Water Areas

 

Where the water hardness exceeds 200mg/litre, it is 

recommended that a proprietary scale reducing device is fitted 

into the boiler cold supply within the requirements of the local 

water company.

IMPORTANT.

 Provision must be made to accommodate the 

expansion of DHW contained within the appliance.  If the DHW inlet 

contains a back flow prevention device or non-return valve, e.g. a 

water meter, then a mini expansion vessel should be fitted between 

the device and the boiler in the cold inlet pipe.

Note.  

DHW Expansion Vessel kit available from Ideal.  

Please 

visit www.idealboilers.com to access the Flue and Accessories Guide. 

Notes.
1.

 

It is most important that the correct concentration of the water 

treatment products is maintained in accordance with the manufacturers’ 

instructions. 

2.

 

If the boiler is installed in an existing system any unsuitable additives 

MUST  be removed by thorough cleansing. BS 7593:2006 details the 

steps necessary to clean a domestic heating system.

3.

 

In hard water areas, treatment to prevent lime scale may be necessary 

-  however the use of artificially softened water is NOT  permitted.

4.

 

Under no circumstances should the boiler be fired  before the system 

has been thoroughly flushed.

For further information contact:

Fernox Cookson Electronics

 

Forsyth Road, Sheerwater, Woking, Surrey GU21 5RZ 

+44 (0) 870 601 5000

Sentinel Performance Solutions 

The Heath Business & Technical Park 

Runcorn, Cheshire WA7 4QX 

Tel: 0800 389 4670

Scalemaster Water Treatment Products

 

Emerald Way, Stone, Staffordshire ST15 0SR 

Tel: +44 (0) 1785 811636

Calmag Ltd.

 

Unit 3-6, Crown Works, Bradford Road,  

Sandbeds, Keighley, West Yorkshire BD20 5LN 

Tel: +44 (0) 1535 210 320

Adey Professional Heating Solutions

Gloucester Road, Cheltenham GL51 8NR

Tel: +44 (0) 1242 546700

Summary of Contents for LOGIC CODE COMBI ESP1 26















































































Reviews: