background image

26

Concord CXi  -  

Installation

31 DESCRIPTION AND OPERATION OF BOILER CONTROLS - continued

procedure should be followed but the [NO] button pressed.

PROGRAMME HOURS

Enables a user-timed programme to be entered.

The following display will be available:-

with the hours, 06, flashing

Using the [UP] or [DOWN] button, select the correct hour and
press [ENTER]. The 

minutes

 will now flash and the correct

minutes should be selected, using the [UP] or [DOWN] button,
followed by pressing [ENTER].  This will cause the hours to
flash and, if the correct ON time has been entered, the [EXIT]
button should be pressed. The display will now show the OFF
for time zone 1.

This procedure should be repeated for all 3 time zones for
Monday.

After the last [EXIT] the display will ask if this day's
programmes require to be copied to Tuesday. If the [YES]
button is pressed Tuesday's programme will be the same as
Monday. This action can be repeated for all the days or as
many as required,

If the [NO] button is pressed then all 3 time slots will need to
be programmed with the required times.

TEMPERATURE SET POINT

Enables the temperature at which the boiler is required to
operate to be set. It has a range of 60 

o

C - 85

o

C.

Using the [UP] or [Down] button, select the TEMP SET from
the menu and press [ENTER].  The following will be
displayed:-

with the temperature flashing.

The [UP] and [DOWN] button should be pressed until the
correct temperature is selected and then the [ENTER] button
should be pressed - the temperature selected will become
stationary.  Pressing the [EXIT]  button will ensure that the
control accepts the new setting and return to the menu.

High / Low Operation

In the example above, when the boiler flow temperature is
equal to 82

 o

C the high rate gas valve will close, allowing the

boiler to run at low rate. When the flow temperature exceeds
the set temperature by 3 

o

C (in the example above, 85

 o

C)  the

low rate gas valve will close and the boiler will be off. The
information screen will display

The boiler will remain OFF for a minimum of 3 minutes or until
the boiler flow temperature has dropped by 3

 o

C, whichever is

the greater time.

If the boiler load is such that it cycles between high and low

operation the boiler will fall through 3 degrees before the high
rate gas valve is energised.

Delayed High Rate Gas Valve Operation

When the boiler is started from cold the high rate gas valve will
be delayed for 3 minutes and then energised. If the boiler flow
temperature is equal to or greater than 55 

o

C then this delay

will NOT occur.

Notes.

1.

If a fault occurs with the boiler thermostat the fault
display screen will show "C/H Sensor Fault".

2.

When the low rate gas valve is de-energised, as the
temperature required has been obtained, the boiler will
go into an anti-cycle route for 2 minutes. The display will
indicate anti-cycle and the current flow temperature.

SERVICING

The SERVICE option is intended as a memory aid to the more
comprehensive servicing instructions to be found in this
manual.

Using the [UP] or [DOWN] button select "Service" from the menu
and press [ENTER].  The following display will be available:-

The 2 screens will alternate to display this whole message.
When using this option, arrow keys will be in evidence to
indicate if the [UP] or [DOWN] buttons should be used. It is
IMPORTANT that these instructions are carried out precisely
and in the order displayed.

COMMISSIONING

The "Commissioning" option is intended as a memory aid to
the more comprehensive commissioning instructions to be
found in this manual.

Using the [UP] or [DOWN] button select "Commissioning" from
the menu and press [ENTER].  The following display will be
available:-

The 2 screens will alternate to display this whole message.
When using this option arrow keys will be in evidence to
indicate if the [UP] or [DOWN] buttons should be used. It is
IMPORTANT that these instructions are carried out precisely
and in the order displayed.

FAULT DIAGNOSIS

In the unlikely event of a fault condition the microprocessors
will identify the fault area, displaying a message indicating the
nature of the fault to assist a speedy and effective repair.

See "Fault Finding" section for more details.

INSTALLATION

INST

ALLA

TION

Summary of Contents for Concord CXi 110









































Reviews: