background image

32

Concord CX 

- Installation

Key No.

Description

Qty.

 Product No.

12D

Boiler body insulation ................................ CX 40

1

150 093

.................................................................. CX50/60

1

150 094

.................................................................. CX70/80

1

150 095

.................................................................. CX90/100

1

150 096

23

Centre main burner ................................... Worgas 0.087.751 CX 40

1

150 153

.................................................................. Worgas 0.087.753 CX 50 / 60

1

150 154

.................................................................. Worgas 0.087.755 CX 70 / 80

1

150 155

.................................................................. Worgas 0.087.757 CX 90 / 100

1

150 156

24

End main burners ...................................... Worgas 0.087.750 CX 40

2

150 149

.................................................................. Worgas 0.087.752 CX 50 / 60

2

150 150

.................................................................. Worgas 0.087.754 CX 70 / 80

2

150 151

.................................................................. Worgas 0.087.756 CX 90 / 100

2

150 152

26

Main burner injectors ................................. Size 3.4 mm; CX 40

3

111 323

.................................................................. Size 3.82mm; CX 50

3

111 324

.................................................................. Size 4.12mm; CX 60

3

111 325

.................................................................. Size 4.57mm; CX 70

3

111 326

.................................................................. Size

 

4.86mm; CX 80

3

013 177

.................................................................. Size 5.2mm; CX 90

3

111 328

.................................................................. Size

 

5.3mm; CX 100

3

013 179

27

Pilot burner  - HONEYWELL Q 349 A1067 complete with 56 /42A injector

1

077 105

28

Pilot burner injector - HONEYWELL 56 / 42A

1

004 545

29

Gas control valve - HONEYWELL V4600C 1391 

1/2

 in. CX40/60

1

111 265

.

Gas control valve - HONEYWELL V4400C 1369 

3/4

 in. Softlite (white button)

CX70/100

1

111 757

30

Spark generator (less bracket) - VERNITRON 60080/002

1

003 939

32

Ignition electrode and H.T. lead assembly - VERNITRON

1

130 947

33

Thermocouple- HONEYWELL Q 309 A-2762,  1200mm long

1

002 937

34

Thermocouple interrupter lead assembly (thermocouple to overheat 'stat.)

1

132 009

35

Thermocouple interrupter lead assembly (overheat 'stat. to gas valve)

1

135 944

37

Electronic  thermostat sensor assembly - PACTROL, 2450 mm long

1

013 459

38

Thermostat potentiometer assembly

1

111 809

39

Thermostat knob

1

013 241

40

Overheat thermostat / bracket assembly - RAK 77.4/3836

1

170689

41

Control box assembly, complete with the front panel and back panel
assemblies plus printed circuit boards 'No.1C' and 'No.6A', fascia panel,
and the control knob.

1

112 092

42

Printed circuit board 'No.1C'

1

060 562

43

Printed circuit board  'No. 6A'

1

060 554

SHORT LIST OF PARTS

When ordering spare parts please quote:

1.

Boiler model

2.

Boiler serial no. (refer to the data plate on the combustion chamber)

3.

Boiler B.G. P.I. No. (refer to the data plate on the combustion chamber)

4.

Description

5.

Quantity

6.

Product no.

The following are parts commonly
required as replacements, due to damage
or expendability.

Their failure or absence is likely to affect
the safety and/or performance of this
appliance.

Summary of Contents for Concord CX-100





































Reviews: