background image

Caradon Plumbing Ltd., PO Box 103, National Avenue, Kingston upon Hull, HU5 4JN.  Telephone: 01482 492251  Fax: 01482 448858.

U.I.N. 1

11 303 A0

Further information

If you would like information about Ideal Boilers please complete this
sheet and fax it to us on 01482 498699 or post it to Caradon Plumbing
L

i

m

i

t

e

d

,

PO Box 103, National Avenue, Kingston upon Hull, HU5 4JN.

Installer details

Name

Address

Post Code

Telephone (

Please include STD code

)

General information required

Please send me details of Ideal Training Courses.
Please arrange for a technical representative to contact me.
Please arrange for me to join an Ideal factory tour.

Range guides required

The Ideal Guide: a specifier's and installer's introduction to the
Ideal domestic boiler range.

The Ideal Householders Guide: to assist the installer when
presenting to his/her customers.

Technical manuals required

The Ideal C class combi boiler
The Ideal Classic wall hung boiler
The Ideal Classic System wall hung boiler
The Ideal Classic LX Deluxe wall hung boiler
The Ideal Mexico floor standing boiler
The Ideal Minimiser heat-saving boiler
The Ideal Response combi boiler
The Ideal Response SE super efficiency combi boiler
The Ideal Systemiser SE super efficiency system boiler
The Ideal Concord high output boiler
The Ideal Buccaneer oil fired boiler

Ideal Installer/Technical Helpline: 01482 498376

Summary of Contents for Concord CX-100





































Reviews: