Ideal Heating LOGIC COMBI2 C24 Installation & Servicing Download

Page: 11 / 70

Installation and Servicing

Section 1 - General

1.14 BOILER DIMENSIONS, SERVICES & CLEARANCES

The boiler connections are made on the boiler connection
tails.

The following minimum clearances must be maintained

for operation and servicing.

Additional space will be required for installation, depending
upon site conditions.

Side and Rear Flue

Provided that the flue hole is cut accurately, e.g. with a core

drill, the flue can be installed from inside the building where

wall thicknesses do not exceed 600 mm.

Front Clearance

The minimum front clearance when built in to a cupboard is
5 mm from the cupboard door but 450 mm overall clearance
is still required, with the cupboard door open, to allow for
servicing.

Bottom Clearance

Bottom clearance after installation can be reduced to 5 mm.

This must be obtained with an easily removable panel to
provide the 100 mm clearance required for servicing.

395

43.5

Refer to Section

2.17

278

700

100*

Flue

terminal

2.5

from case

Underside View - Dimension to Wall

Flow

DHW

Outlet

Gas

DHW

Inlet

Return

CH Circuit

Drain

Cond.

Drain

200

152

PRV Grommet

Refer to Section

2.17

IMPORTANT:

Please ensure there is sufficient

clearance either side and below the boiler, particularly from
door hinges and the base of a cupboard.

Measurements in mm

PRV

Grommet

43.5

Water and Gas Connections

Data

Plate

Flow

DHW

Outlet

PRV

Grommet

Return

DHW

Inlet

Gas

Inlet

Cond.

Drain

Measurements in mm

Summary of Contents for LOGIC COMBI2 C24







































































Search results

Summary of Contents for LOGIC COMBI2 C24

Reviews:

Related manuals for LOGIC COMBI2 C24

Brands by name

Popular brands

Ideal Heating LOGIC COMBI2 C24, Installation & Servicing

Search results

Summary of Contents for LOGIC COMBI2 C24

Reviews:

Related manuals for LOGIC COMBI2 C24

Brands by name

Popular brands