manualshive.com logo in svg

Ideal Heating ECOMOD AHP60 50 kW, Installation And Servicing, Page: 32 / 78

Share
Download
Ideal Heating ECOMOD AHP60 50 kW Installation And Servicing Download Page 32

32 / 78 

 00U07352260-A_EN

AHP60-50/70  -  

Installation, Use and Maintenance

3.4.  Installing the control unit

The Ecomod Heat Control control unit for the heat pump is supplied separately, with a specific 

installation guide inside its packaging. Refer to this guide to connect this unit.

3.5. 

Position of the centre of gravity and the vibration shock absorbers

The position of the centre of gravity of each heat pump is indicated in the table, with reference 

to the dimensions indicated in the image. 

A

P1

P2

P3

P4

A

B

Yb

Xb

Models

A [mm]

B [mm]

Xa [mm]

Yb [mm]

ECOMOD AHP60 

50 kW

1110

1754

652

517

ECOMOD AHP60 

70 kW

1110

1754

683

511

The positions laid down for the installation of the vibration shock absorbers for each type of heat 

pump are presented in the image below.

74

90

90

Ø

8,5

P1

P2

P3

P4

A

B

C

D

D

Summary of Contents for ECOMOD AHP60 50 kW















































































Reviews:

No comments