background image

25

Mexico Super CF 3/100, 3/125, 3/140 - 

Installation

40 CONTROL THERMOSTAT  REPLACEMENT

SERVICING

41 CONTROLS PANEL REPLACEMENT

1.

Lift off the front door. Refer to
Frame 28.

2.

Pull off the thermostat knob.

3.

Remove the 2 screws and pull
down the control panel so that
the tabs clear the top panel.

4.

Remove the thermostat phial
from the pocket. Refer to Frame
28.

5.

Remove the bottom screw and
remove the cover from the
control box.

6.

Remove the top screw and ease
the control box off the control
panel.

7.

Remove the 2 screws to release
the thermostat bracket.

8.

Disconnect the electrical leads
from the thermostat.

9.

Unscrew the thermostat nut to
withdraw the thermostat.

10.

Fit the new thermostat and re-
assemble in reverse order.

1.

Lift off the lower front panel. Refer Frame 28

2.

Pull off the thermostat knob.

3.

Disconnect the electrical connections
from the gas valve.

4.

Unscrew the 2 screws and pull down the
control panel so that the 2 tabs clear the
top panel.

5.

Remove the thermostat phial from the
pocket. Refer to Frame 28.

6.

Remove the bottom screw and remove
the cover from the control box.

7.

Remove the top screw and ease the
control box off the control panel.

8.

Disconnect the mains electrical supply
from the terminal strip and release from
its clamp.

9.

Remove the 2 screws to release the
thermostat bracket.

10.

Disconnect the TTB thermostat leads
from the terminal strip and control
thermostat. Then release from its bush.

11.

On the new control box gain access to
the control thermostat as described
above.

12.

Discard the control thermostat lead that
connects to terminal strip marked 'L

G

'.

13.

Reconnect the TTB thermostat lead to the control thermostat and
terminal strip marked 'L

G

'.

14.

Assemble new control box and panel and fit to the casing reverse order.

SER

VICING

Summary of Contents for CF#/125





































Reviews: