manualshive.com logo in svg

IdeaFly Hero-550, User Manual, Page: 9 / 26

Share
Download
IdeaFly Hero-550 User Manual Download Page 9

9 

 

⑤    number of cells 

 

⑥  In order to prevent your multi-rotor from a crash or other harmful consequences caused by 

low battery voltage  ，there are two levels of low battery protection available to use. 

 

 

 

Make sure Carefully read Lipo Battery Safety Guide :   

********************************************************* 

Notice :LIPO Batteries and LIPO chargers CAN ignite and cause fire.   

These cautions MUST be followed 

1. Never charge a LIPO battery if it is hot to the touch. 

2. Never charge a damaged or broken LIPO Battery. 

3. ONLY CHARGE ON A FIREPROOF SURFACE. 

4. DO NOT CHARGE UNATTENDED. 

Enter the voltage per cell required to activate a low voltage alert, for a Lipo battery this would 

  be normally be 3.65v. 

Note:   

1、Both levels of protection have LED warning as default. Both levels of protection 

  will blink red continuously. 

2、When there is no power, aircraft will auto-land. 

3、The MC can calculate final stage low voltage according to the Cell Number and First stage 

  low voltage alert    Final stage value= (First stage low voltage alert - 0.05v) * Cell Number     

Summary of Contents for Hero-550



























Reviews:

No comments