manualshive.com logo in svg

IdeaFly Hero-550, User Manual, Page: 2 / 26

Share
Download
IdeaFly Hero-550 User Manual Download Page 2

2 

 

Disclaimer 

Please read this disclaimer carefully and follow instructions on assembly and calibration contained 

in  this  manual.  By  using  our  product,  you  hereby  agree  to  this  disclaimer  and  signify  that  you  have 

read the entire manual thoroughly. 

THIS PRODUCT IS NOT SUITABLE FOR PEOPLE UNDER THE AGE OF 18. 

This product is not a toy! It is a complicated combination of mechanics, electronics, aerodynamics 

and  high-frequency  radio  technologies.  Users  should  strictly  obey  safety  operation  specification  on 

aerial  model  and  follow  steps  illustrated  in  the  manual  to  install  and  calibrate  the  product.  Idea-Fly 

takes no responsibility for any direct or indirect damage(s) or injuries caused by improper installation, 

calibration and operation. 

Idea-Fly  takes  no  responsibility  for  any  direct  or  indirect  damage(s)  or  injuries  caused  by 

installing/calibrating/flying  this  product  when  users  are  in  situations  including  but  not  limited  like 

drunk, taking drugs, dizziness, fatigue or any other cases no matter mentally or physically that would 

impair your ability. 

Idea-Fly takes no responsibility for any direct or indirect damage(s) or injuries caused by flying this 

product in inappropriate whether like windy (no more than gentle wind), rain, snow, hail, lightning or 

any natural disaster. 

Idea-Fly takes no responsibility for any direct or indirect damage(s) or injuries caused by using this 

product  in  inappropriate  area  like  magnetic  or  radio  interference  area,  government  regulated  no-fly 

zone or any other not permitted public or private areas. 

Idea-Fly takes no responsibility for any direct or indirect damage(s) or injuries caused by using this 

product  assembled  with  parts  NOT  produced  by  Idea  Fly,  incomplete/incorrect  assembly  or  Idea-Fly 

Summary of Contents for Hero-550



























Reviews:

No comments