ICU Eve Mini Owner'S Manual Download Page 11

11

ENGLISH

EN

5.1 Back End Systems

You  are  in  possession  of  an  intelligent  ICU  char-

ging station that can communicate with a back end 

system  through  an  internet  connection.  Back  end 

systems allow you for example to view the energy 

consumption  of  individual  users,  remotely  control 

charging or monitor the charging station for service 

purposes.
 
If you signed a contract with a back end supplier or 

with Alfen  ICU  B.V.  (for  provision  of  ICU  EZ  back 

end services), your charging station is configured to 

connect to the respective back end ex-factory. The 

internet  connection  may  be  facilitated  via  GPRS 

(SIM card) or via UTP (Ethernet) cable connection.

In case you opted for a GPRS (SIM card) connec-

tion, your charging station is already equipped with 

the correct SIM card. The charging station will es-

tablish a connection to the internet as soon as it is 

turned on. In case there is no SIM card in the SIM 

Card Slot, please contact your back end provider or 

Alfen ICU.
 
The following paragraphs describe how to connect 

your  charging  station  via  UTP  (Ethernet)  cable  to 

the internet.

5.2 UTP (Ethernet) connection

Which cable is required?

A UTP cable of minimally CAT5 is needed to con-

nect the charging station to the Internet. This cable 

is suitable for speeds up to 100Mbps.

Installation

1.  Connect the UTP cable to your router
2.  Turn off the power of the charging station by 

putting the main switch to the 0 position

3.  Connect the UTP cable to the Communication 

Unit  of  the  charging  station  (

12

 on the left of 

the cover)

4.  Turn on the power of the charging station by 

putting the main switch to the 1 position

5.  In order for your charging station to communi-

cate with ICU EZ through a wired UTP ethernet 

connection, your network setting should be ad-

justed if these are additionally secured. Below 

you will find the necessary information to allow 

access through your network:

•  IP address ICU EZ: 93.191.128.6
•  Port: 9090
•  Inbound – Outbound

It may be possible that a MAC address is required. 

This is stated on the FAT report of the charging 

station. This report can be provided by Alfen ICU. 

 

Please also make sure that your network settings 

allow the charging station to run diagnostics and up-

dates via a secure FTP connection to ICU servers. 

NOTICE

 

5. Connectivity

Connectivity

Summary of Contents for Eve Mini












Reviews: