background image

SERVICE AND TECHNICAL SUPPORT MANUAL

Gas Furnace: N9MSB

Specifications  subject to change without notice.

440 04 4413 03

11

Table 3 (CONT.)

Orifice Size and Manifold Pressure (in. w.c.) for Gas Input Rate 

 Single Stage

A11253B

S

A

G

L

A

R

U

T

A

N

F

O

Y

T

I

V

A

R

G

C

I

F

I

C

E

P

S

S

A

G

.

G

V

A

HEAT VALUE

0.58

0.60

0.62

0.64

AT ALTITUDE

Orifice

Manifold

Orifice

Manifold

Orifice

Manifold

Orifice

Manifold

(Btu/cu ft)

No.

Pressure

No.

Pressure

No.

Pressure

No.

Pressure

ALTITUDE

RANGE

ft (m)

SINGLE-STAGE FURNACE

(TABULATED DATA BASED ON 20,000 BTUH PER BURNER, DERATED 2%/1000 FT (305M) ABOVE SEA LEVEL)

650

42

3.4

42

3.5

42

3.6

42

3.7

7001

675

43

3.8

42

3.2

42

3.3

42

3.4

(2134)

700

43

3.5

43

3.7

43

3.8

42

3.2

725

44

3.8

43

3.4

43

3.5

43

3.6

750

44

3.5

44

3.7

44

3.8

43

3.4

8000

775

44

3.3

44

3.4

44

3.5

44

3.7

(2438)

800

44

3.1

44

3.2

44

3.3

44

3.4

825

44

2.9

44

3.0

44

3.1

44

3.2

625

42

3.4

42

3.5

42

3.6

42

3.7

8001

650

43

3.8

42

3.2

42

3.3

42

3.4

(2439)

675

43

3.5

43

3.6

43

3.7

42

3.2

700

44

3.7

43

3.4

43

3.5

43

3.6

725

44

3.5

44

3.6

44

3.7

44

3.8

9000

750

44

3.3

44

3.4

44

3.5

44

3.6

(2743)

775

44

3.0

44

3.2

44

3.3

44

3.4

9001

600

42

3.3

42

3.4

42

3.6

42

3.7

(2744)

625

43

3.7

42

3.2

42

3.3

42

3.4

650

43

3.5

43

3.6

43

3.7

43

3.8

675

44

3.7

44

3.8

43

3.4

43

3.5

10000

700

44

3.4

44

3.5

44

3.7

44

3.8

(3048)

725

44

3.2

44

3.3

44

3.4

44

3.5

* Orifice numbers shown in

BOLD

are factory-installed.

to

to

to

U.

S

.A.

On

ly

U.

S

.A.

On

ly

U.

S

.A.

On

ly

Adjust Temperature Rise

NOTE

:  Blower door must be installed when taking temperature

rise reading. Leaving blower door off will result in incorrect

temperature measurements, due to possible changes in duct
static pressure and airflow.

FURNACE DAMAGE HAZARD

Failure to follow this caution may result in:

S

Overheating the heat exchangers or condensing

flue gases in heat exchanger areas not designed

for condensate.

S

Shortened furnace life.

S

Component damage.

Temperature rise must be within limits specified on furnace

rating plate. Recommended operation is at midpoint of rise

range or slightly above.

CAUTION

!

Jumper R to W to check gas-heat temperature rise. Do not

exceed temperature rise ranges specified on unit rating plate.
This furnace must operate within the temperature rise ranges

specified on the furnace rating plate. Determine the air

temperature as follows:

1. Place duct thermometers in return and supply ducts as

close to furnace as possible. Be sure thermometers do

not “see” heat exchangers so that radiant heat does not

affect thermometer readings. This is particularly

important with straight

run ducts.

2. When thermometer readings stabilize, subtract return

air

temperature from supply

air temperature to determine

temperature rise.

If the temperature rise is outside this range, check the

following:

1. Gas input rate.
2. Derate for altitude if applicable.
3. Return and supply ducts for excessive restrictions

causing static pressures greater than 0.50

in. w.c. (125

Pa)

4. Adjust temperature rise by adjusting blower speed.

S

Increase blower speed to reduce temperature rise.

S

Decrease blower speed to increase temperature rise.

ELECTRICAL OPERATION HAZARD

Failure to follow this warning could result in personal injury

or death.
Disconnect 115vac electrical power before changing speed

tap.

!

WARNING

Summary of Contents for N9MSB































Reviews: