2
3
D
ETECTION ZONE
.............................................................................................................................................. 10
TECHNICAL FEATURES ........................................................................................................................................ 10
WARRANTY ....................................................................................................................................................... 10
DECOMMISSIONING ........................................................................................................................................... 11
FURTHER INFORMATION .................................................................................................................................... 11
1
L
EGAL NOTIFICATION
......................................................................................................................................... 11
V
ERSION
........................................................................................................................................................ 11
T
HE MANUFACTURER
ILLUSTRATIONS TABLE
FIGURE 1: DELIVERY ............................................................................................................................................. 4
FIGURE 5: TMA-011 LV AND MV RADAR CONNECTOR - WEIPU SP1712/P9 ............................................................. 6
FIGURE 6: TMA-011 HV RADAR CONNECTOR - WEIPU SP2112/P7 .......................................................................... 6
FIGURE 5: TMA-011 LV AND MV RADAR CONNECTOR - WEIPU SP1712/P9 ............................................................. 8
FIGURE 6: TMA-011 HV RADAR CONNECTOR - WEIPU SP2112/P7 .......................................................................... 8
FIGURE 6: FRONT FACE
FIGURE 7: ENCODERS & LEDS ....................................................................................... 8
FIGURE 8: FRONT FACE WITHOUT/WITH STICKER .................................................................................................. 8
FIGURE 9: TILT OR INSTALLATION ANGLE .............................................................................................................. 9
FIGURE 10: DETECTION ZONE AT 0.5M DISTANCE FROM THE PAVEMENT, H = 3,5M, 10°TILT ANGLE, DETECTION DISTANCE 16 M. ................................................................................................................................................. 10
