background image

 

 

10 

3.

 

Place the radar on the top of the traffic light, aiming the on-
crossing: 

4.

 

Firmly tighten the screws. 

 

D

ETECTION ZONE

 

 

Figure 10: Detection zone at 0.5m distance from the pavement, H = 3,5m, 10°tilt angle, detection distance 16 m. 

 

This drawing shows the theoretical radar lobe and does not consider environmental variables. This drawing is for 
indication purpose only. 

TECHNICAL FEATURES 

 

TMA-011-LV 

TMA-011-MV 

TMA-011-HV 

Protection level 

IP 65 

Power supply 

10-30V AC, 50-60 Hz 

12V-60V DC 

15-54V AC, 50-60 Hz 

21-75V DC 

100V –240V AC, 50-60 Hz 

Power consumption 

@12V DC: < 1.2 W 

@220V AC: < 2 W 

User output 

 

Inverted relay contact - Resistive load: 30V AC 0.3 A – 60V DC 0.3 A 

 

Option 250 V relay: 250 V AC - 30 V DC – 0.3 A 

 

2 LED outputs on front face 

Temperature range 

-40° C to +60° C 

Dimensions 

68 mm x 99 mm x 119 mm 

68 mm x 99 mm x 180 mm 

Weight 

350 g 

460 g 

485 g 

Wiring & connectors 

Weipu connector 

WARRANTY 

Icoms Detections warrants its hardware products to be free from defects in workmanship and materials, under 
normal use and service, for a period of two (2) years from the date of dispatch from Icoms Detections premises, 
except for the batteries for which a warranty period of six (6) months applies. 

Summary of Contents for TMA-011












Reviews: