–
3
–
–
2
–
D
For the power adapter
R
WARNING! NEVER
use the power adapter with
any device other than the IP1000C. This may result in
an electrical shock, cause a fire or damage the power
adapter.
R
WARNING! CONNECT
the adapter into an outlet
between 100 V and 240 V AC. Otherwise, this may
result in an electrical shock, cause a fire or damage
the power adapter.
R
WARNING! NEVER
install the power adapter to
wet place outside or near a humidifier. This may
result in an electrical shock, cause a fire or damage
the power adapter.
R
WARNING! NEVER
put something heavy on the
power adapter cable. This may result in an electrical
shock, cause a fire or damage the power adapter.
R
WARNING! NEVER
modify, bend by force, twist,
pull or heat the power adapter’s cable. This may result
in an electrical shock, cause a fire or damage the
power adapter.
R
WARNING! NEVER
touch the power adapter with
wet hands. This may result in an electrical shock or
damage the power adapter.
R
WARNING!
Use and place the power adapter and
connection cable to avoid inadvertent use by children.
This may result in an electrical shock or cause injury.
D
Other precautions
• For information about operating the PC or external
devices, refer to their instruction manuals for
details.
•
The supplied power adapter may at some
time need to be replaced, depending on its life
expectancy. The life of a power adapter differs
according to the environment or condition in which
the adapter is used.
We recommend replacement when it has been
used for approximately 5 years (When used under
the ambient temperature of 25°C; 77°F). Contact
your local dealer for details.
Precautions
D
For the IP1000C
R
WARNING! NEVER
use other than the supplied
power adapter. This may result in an electrical shock,
cause a fire or damage the IP1000C.
R
WARNING! NEVER
attempt to connect the power
adapter to other than the [DC] jack on the IP1000C
rear panel. This may result in an electrical shock,
cause a fire or damage the IP1000C.
R
WARNING! NEVER
disassemble, modify or repair
the IP1000C. This may result in an electrical shock,
cause a fire or damage the IP1000C.
R
WARNING! NEVER
install the IP1000C in a wet
place or outside. This may result in an electrical
shock, cause a fire or damage the IP1000C.
R
WARNING! NEVER
operate or touch the IP1000C
with wet hands. This may result in an electrical shock
or damage the IP1000C.
R
WARNING! NEVER
connect the ground terminal to
a gas or electric pipe. This may result in an electrical
shock or cause a fire.
R
WARNING! NEVER
use the IP1000C during a
lightning storm. It may result in an electric shock,
cause a fire or damage the IP1000C. Always
disconnect the power adapter before a storm.
R
WARNING!
Immediately disconnect the power
adapter if the IP1000C emits an abnormal odor, sound
or smoke. Contact your Icom dealer or distributor for
advice.
R
WARNING! NEVER
put the IP1000C in any
unstable place (such as on a slanted surface or
vibrating place). This may cause injury and/or damage
to the IP1000C.
CAUTION: NEVER
install the IP1000C in a place
without air vents. Heat dissipation may be reduced,
and this could damage the IP1000C.
CAUTION: DO NOT
use or place the IP1000C in
areas with temperatures below 0°C (+32°F) or above
+40°C (+104°F).
CAUTION: DO NOT
place the IP1000C in direct
sunlight. This could damage the IP1000C.
CAUTION: DO NOT
use the IP1000C in strong
magnetic fields or in an area with high static electricity.
This could damage the IP1000C.
CAUTION:
Disconnect the power adapter when you
will not use the IP1000C for a long period of time.
CAUTION: DO NOT
use harsh solvents such as
Benzine or alcohol when cleaning, because they will
damage the IP1000C’s surfaces.
Always place the IP1000C in a secure place to avoid
inadvertent contact with unauthorized persons.
Initializing the IP1000C
If you cannot access the IP1000C setting screen, you can initialize (reset) the IP1000C by pushing [INIT] on the
rear panel.
•
This initializing resets all settings to the factory defaults.
•
See the IP1000C instruction manual for initializing from the setting screen.
L
Indications other than the specified below may differ, depending on the network environment.
1.
Disconnect all cables from the IP1000C, and then
connect the power adapter.
L
Verify that the [PWR] indicator lights green.
2.
Push in and hold [INIT] on the rear panel with
a pin until all indicators on the front panel light
orange, and then release.
•
The initialization starts.
•
When the initialization has been completed, [PWR]
lights green.
:Black out
<Status>
[LED indication]
[Operation]
:Light
:Blink
Turn ON the IP1000C
Use
a pin
Power
adapter
後面部
Rear
panel
[INIT]
Push in and hold
Release
Lights
(Green)
Lights
(Green)
Blinks
(Orange)
Lights
(Orange)
Blinks
（
Orange/Green
）
Blinks
(Green)
All LEDs light (Orange)
Lights
(Green)
The firmware update function
The [MSG] LED lights green when an IP1000C firmware update is available.
To use the Firmware Update function, an internet
connection, the DNS and default gateway must be set.
See the IP1000C instruction manual for the setting
details, or contact your Icom dealer or distributor for
advice.
NOTE: NEVER
turn OFF the IP1000C until an
update has completed. Otherwise, the IP1000C
firmware may be damaged.
D
Updating the firmware
If a firmware update is available, the [MSG] lights
green. Follow the procedures below to download and
install the new firmware.
z
Push in and hold [UPDATE] on the front panel with
a pin until [MSG] blinks, and then release.
•
The IP1000C automatically starts download and
updates the firmware, and then reboots.
NOTE:
The IP1000C may automatically update the
firmware without any indication and reboot even
while in use, depending on the updated content.
Disable the automatic update function if you do not
want the IP1000C automatic updates.
Use a pin
Push in
and hold
Front
panel
Release
:Black out
<Status>
[LED indication*]
[Operation]
:Light
:Blink
After the rebooting,
[PWR] lights green.
Lights
(Green)
Blinks
(Green)
All LEDs light (Orange)
L
Indications other than [PWR] and [MSG] may differ, depending on
the network environment (Except for when all LEDs light.)
