background image

WHEN INSTALLING THE DSC UNIT

NEVER 

transmit a distress call when your vessel does not

need immediate help. Distress calls can be used only in times
of emergency.

AVOID 

using or placing the transceiver in direct sunlight or

in areas with temperatures below –20°C (–4°F) or above
+60°C (+140°F).

DO NOT

operate the transceiver without running the ves-

sel’s engine. When your vessel’s engine is OFF and the
transceiver is transmitting, the vessel’s battery will soon be-
come exhausted.

KEEP 

the transceiver out of the reach of children.

KEEP 

the antenna cable and DC power cable as far away

as possible from electrical pumps, generators and other elec-
tronic instruments to prevent instrument malfunctions.

KEEP 

the transceiver and microphone at least 1 meter

away from your vessel's magnetic navigation compass.

iii

IMPORTANT

READ ALL INSTRUCTIONS

carefully and com-

pletely before using the transceiver.

SAVE THIS INSTRUCTION MANUAL—

This in-

struction manual contains important operating instructions for
the IC-M59.

YOU MUST HAVE

a DSC vessel ID in order to oper-

ate the optional DSC functions of the transceiver. See your
Dealer for details.

CAUTIONS

R

WARNING NEVER

connect the transceiver to an

AC outlet. This may pose a fire hazard or result in an electric
shock.

R

WARNING HIGH VOLTAGE! NEVER

touch

the antenna or an internal antenna connector during trans-
mission. This may result in an electric shock or a burn.

NEVER

connect the transceiver to a power source of more

than 16 V DC. This connection will ruin the transceiver.

Summary of Contents for IC-M59





































Reviews: