Icom IC-F9011B Operating Manual Download Page 45

Page: 45 / 70

APCO P25 MODE OPERATION

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

Push

[PTT] to transmit the remote monitor signal to the

target station.

• The LED indicator

(for Handhelds) or Transmit indicator (for Mo-

biles) lights red.

• “

PLEASE WAIT” is displayed.

Release

[PTT].

• “

ACK RECEIVED” is displayed after receiving an acknowledge-

ment from the target station, and then the transceiver returns to
normal operation.

• The LED indicator

(for Handhelds) or Transmit indicator (for Mo-

biles) lights green.

• “

NO ACKNOWLDG” is displayed when an acknowledgement is

not received, and then transceiver returns to normal operation.

Receiving

➥

When a remote monitor signal is received, the transceiver

automatically transmits an acknowledgement and audio*.

* The audio is transmitted for a pre-set time period.

• The LED indicator

(for Handhelds) or Busy indicator (for Mobiles)

lights green while receiving, and lights red while transmitting an
acknowledgement or the audio.

✔

For Mobile transceivers operation:

When the optional SM-25

desktop

microphone

, HM-152T or

HM-148T

hand

microphones

is connected, the audio will not

be transmitted.

Summary of Contents for IC-F9011B







































































Search results

Summary of Contents for IC-F9011B

Reviews:

Brands by name

Popular brands

Icom IC-F9011B, Operating Manual

Search results

Summary of Contents for IC-F9011B

Reviews:

Brands by name

Popular brands