manualshive.com logo in svg

Icom IC-F4SR, Instruction Manual

Share
Download
Icom IC-F4SR Instruction Manual Download Page 8

4

2

PANEL DESCRIPTION

■

Function display

q

SELECT CHANNEL MODE INDICATOR (p. 7)
Appears when select channel mode is selected. Disap-
pears when all channel mode is selected.

w

LOCK INDICATOR (p. 6)
Indicates that the lock function is in use.

e

INVERSE DTCS CODE INDICATOR (p. 12)
Appears when setting an inverse DTCS code.

r

TONE SQUELCH/DTCS INDICATOR (p. 12)
Appears when setting a tone squelch frequency or DTCS
code, etc.

t

RINGER INDICATOR (p. 10)
“

S

” appears while transmitting a ringer signal.

y

POCKET BEEP INDICATOR (p. 14)
“

ë

” appears during pocket beep operation.

u

RECEIVE TONE/DTCS SQUELCH OFF INDICATOR

➥

Appears when the receive tone/DTCS squelch is turned
OFF. (p. 12)

• This function is not available for some versions.

➥

Appears when the monitor function is in use. (p. 6)

i

LOW BATTERY INDICATOR

➥

Appears when the battery is nearing exhaustion.

➥

Appears and flashes when battery replacement is nec-
essary.

o

CHANNEL READOUT
Shows the operating channel, tone frequency, DTCS code,
set mode contents, etc.

!0

BUSY AND SIGNAL INDICATORS

➥

“BUSY” appears when receiving a signal or when the
squelch is open.

➥

The signal indicators show the relative signal strength
while receiving.

!1

NON-SELECT CHANNEL INDICATOR (p. 7)
Appears when a non-select channel is selected.

MR

BUSY

T SQL

SKIP

!0

q w e

r

y

i

u

t

o

!1

!0

Summary of Contents for IC-F4SR





























Reviews:

No comments

Brands by name

Popular brands

Load more brands