manualshive.com logo in svg

Icom IC-F4SR, Instruction Manual

Share
Download
Icom IC-F4SR Instruction Manual Download Page 26

22

10

SPECIFICATIONS

D

General

• Frequency coverage (Incl. all SRBR ch.):

U.K.

461.2625–461.4875 MHz

France-1

446.9500–446.9875 MHz

France-2

446.03125–446.09375 MHz

Sweden

444.6000–444.9750 MHz

• Mode :

U.K., France

FM (8K50F3E)

Sweden

FM (16K0F3E)

• Acceptable power supply : 9.6 V DC nominal

(negative ground)

(authorized battery packs)

• Usable temp. range

: –20˚C to +55˚C

• Frequency stability

: ±5 ppm

• Current drain (approx.)

:

Tx

at 0.5 W ERP

0.9 A

Rx

standby 60 

mA

max. audio

250 mA

power saved

20 mA

• Antenna impedance

: 50 

Ω

(nominal)

• Dimensions : 57(W)

✕

140(H)

✕

37(D) mm

(projections not incl.)

• Weight (with BP-195)

: 370 g

D

Receiver

• Receive system

: Double conversion superheterodyne

• Intermediate frequencies : 1st

46.35 MHz

2nd

450 kHz

• Sensitivity

: 0.3 µV at 12 dB SINAD

• Squelch sensitivity

: 0.3 µV typical (at threshold)

• Adjacent ch. selectivity

:

U.K., France

60 dB

Sweden

70 dB

• Spurious response

: 70 dB

• Intermodulation rejection : 65 dB
• Audio output power

: 500 mW typical at 10%

(at 9.6 V DC)

distortion with an 8 

Ω

load

• External SP connector

: 2-conductor 3.5 (d) mm/8 

Ω

D

Transmitter

• Output power

: 0.5 W ERP (at 9.6 V DC)

• Modulation

: Variable reactance frequency

modulation

• Max. frequency deviation :

U.K., France

±2.5 kHz

Sweden

±5 kHz

• Spurious emissions

:

U.K., France

0.25 µW

Sweden

0.25 µW

• Adjacent channel selectivity :

U.K., France

60 dB

Sweden

70 dB

• External mic. connector

: 3-conductor 2.5 (d) mm/2 k

Ω

All stated specifications are subject to change without
notice or obligation.

Summary of Contents for IC-F4SR





























Reviews:

No comments

Brands by name

Popular brands

Load more brands