background image

31

5

MDC 1200 OPERATION

D

D

Transmitting a Message

The transceiver can send a pre-programmed message to the
dispatcher. There are 16 messages that can be sent on a
channel.

q

Push [MDC Call] to enter the MDC menu selection mode.

w

Select “MSG” using [CH Up], [CH Down], [MDC Up] or
[MDC Down].

e

Push [MDC Call] again to enter the pre-programmed mes-
sage selection mode.

r

Select the desired message using [CH Up], [CH Down],
[MDC Up] or [MDC Down].

t

Push [PTT] to transmit the message to the dispatcher.

• “MSG TX” is displayed.

y

Release [PTT].

• “MSG OK” is displayed.
• “MSG FAIL” is displayed if there is no acknowledgment from the

dispatcher.

u

After a specified time period has passed, the transceiver
will return to receive.

D

D

Emergency Calls

The MDC 1200 Emergency feature can be accessed using
the [MDC Emg] key (p. 10). The optional UT-113 

MAN DOWN

UNIT

can also activate this feature. The transceiver will repeat-

edly send an Emergency MDC 1200 command to the dis-
patcher for a programmed length of time until it receives an
acknowledgement signal.

The emergency call can be transmitted without a beep emis-
sion and LCD indication change depends on the setting.
With MDC 1200 Emergency, the transceiver can also be pro-
grammed to keep the microphone open during an emergency
call, allowing monitoring of the situation.
Ask your dealer for details.

D

D

Stun and Revive

The dispatcher can send MDC 1200 signals that will stun or
revive your transceiver. If a Stun command is received that
matches your station ID, the transceiver will display “SORRY”
and you can not receive or transmit. When a Revive com-
mand is received that matches your station ID, normal opera-
tion is restored.

Pre-programmed message is displayed.

IC-F33_43GT_GS_MDC.qxd  06.7.19 2:09 PM  Page 31 (1,1)

Summary of Contents for IC-F43GT

























































Reviews: