![background image](http://html.mh-extra.com/html/icom/ic-f1100d-series/ic-f1100d-series_user-manual_3049851006.webp)
PRECAUTIONS
R
WARNING! NEVER
use or charge Icom battery packs
with non-Icom transceivers or non-Icom chargers. Only
Icom battery packs are tested and approved for use with
Icom transceivers or charged with Icom chargers. Using
third-party or counterfeit battery packs or chargers may
cause smoke, fire, or cause the battery to burst.
R
WARNING! NEVER
hold the transceiver so that the
antenna is very close to, or touching exposed parts of the
body, especially the face or eyes, while transmitting.
R
WARNING! NEVER
operate the transceiver with a
headset or other audio accessories at high volume levels.
The continuous high volume operation may cause a
ringing in your ears. If you experience the ringing, reduce
the volume level or discontinue use.
CAUTION: DO NOT
short the terminals of the battery
pack. Shorting may occur if the terminals touch metal
objects such as a key, so be careful when placing the
battery packs (or the transceiver) in bags, and so on.
Carry them so that shorting cannot occur with metal
objects. Shorting may damage not only the battery pack,
but also the transceiver.
CAUTION: DO NOT
use harsh solvents such as Benzine
or alcohol when cleaning. This could damage the
equipment surfaces. If the surface becomes dusty or dirty,
wipe it clean with a soft, dry cloth.
CAUTION: DO NOT
place or leave the transceiver in
excessively dusty environments. This could damage the
transceiver.
Icom is not responsible for the destruction, damage to, or
performance of any Icom or non-Icom equipment, if the
malfunction is because of:
•
Force majeure, including, but not limited to, fires,
earthquakes, storms, floods, lightning, other natural
disasters, disturbances, riots, war, or radioactive
contamination.
•The use of Icom transceivers with any equipment that is
not manufactured or approved by Icom.
FCC INFORMATION
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause
harmful interference in which case the user will be
required to correct the interference at his own expense.
CAUTION:
Changes or modifications to this transceiver,
not expressly approved by Icom Inc., could void
your authority to operate this transceiver under FCC
regulations.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the condition that this device does
not cause harmful interference.
RECOMMENDATION
CLEAN THE TRANSCEIVER THOROUGHLY IN A BOWL
OF FRESH WATER
after exposure to saltwater, and dry
it before operating. Otherwise, the transceiver’s keys,
switches, and controllers may become unusable, due to
salt crystallization, and/or the charging terminals of the
battery pack may corrode.
NOTE:
If the transceiver’s waterproof protection appears
defective, carefully clean the transceiver with a soft,
damp (fresh water) cloth, then dry it before operating.
The transceiver may lose its waterproof protection if the
case, jack cap, or connector cover is cracked or broken,
or the transceiver has been dropped.
Contact your Icom distributor or your dealer for advice.
Icom, Icom Inc. and the Icom logo are registered
trademarks of Icom Incorporated (Japan) in Japan, the
United States, the United Kingdom, Germany, France,
Spain, Russia, Australia, New Zealand, and/or other
countries.
AquaQuake is a trademark of Icom Incorporated.
AMBE+2 is a trademark and property of Digital Voice
Systems Inc.
All other products or brands are registered trademarks or
trademarks of their respective holders.
EXPLICIT DEFINITIONS
WORD
DEFINITION
R
DANGER!
Personal death, serious injury or an
explosion may occur.
R
WARNING!
Personal injury, fire hazard or electric
shock may occur.
CAUTION
Equipment damage may occur.
NOTE
If disregarded, inconvenience only. No
risk of personal injury, fire or electric
shock.
NOTE: DO NOT
place or leave the transceiver in areas
with temperatures below –25°C (–13°F) or above +55°C
(+131°F): ETS version, below –30°C (–22°F) or above
+60°C (+140°F): TIA version, or in areas subject to direct
sunlight, such as the dashboard.
BE CAREFUL!
The transceiver meets IP67* requirements
for dust tight and waterproof protection. However, once
the transceiver has been dropped, dust protection and
splash resistance cannot be guaranteed due to the fact
that the transceiver may be cracked, or the waterproof
seal damaged, and so on.
* Only when the jack cover, the optional HM-168LWP, HM-
171GPW, HS-94LWP, or HS-95LWP is attached.
D
Battery caution
Misuse of Li-ion batteries may result in the following
hazards: smoke, fire, or the battery may rupture. Misuse
can also cause damage to the battery or degradation of
battery performance.
R
DANGER! NEVER
solder the battery terminals, or
NEVER modify the battery pack. This may cause heat
generation, and the battery may burst, emit smoke or
catch fire.
R
DANGER! NEVER
place or leave battery packs in
areas with temperatures above 60°C (140°F). High
temperature buildup in the battery cells, such as could
occur near fires or stoves, inside a sun-heated vehicle,
or in direct sunlight for long periods of time may cause
the battery cells to rupture or catch fire. Excessive
temperatures may also degrade the battery pack’s
performance or shorten the battery cell’s life.
R
DANGER! NEVER
strike or otherwise impact the battery
pack. Do not use the battery pack if it has been severely
impacted or dropped, or if the pack has been subjected to
heavy pressure. Battery pack damage may not be visible
on the outside of the case. Even if the surface of the
battery does not show cracks or any other damage, the
cells inside the battery may rupture or catch fire.
R
DANGER! NEVER
place battery packs near a fire.
Fire or heat may cause them to rupture or explode.
Dispose of used battery packs in accordance with local
regulations.
R
DANGER! NEVER
let fluid from inside the battery get in
your eyes. This can cause blindness. Rinse your eyes with
clean water, without rubbing them, and immediately get
medical treatment from an eye doctor.
R
WARNING! NEVER
put the battery pack in a microwave
oven, high-pressure container, or in an induction heating
cooker. This could cause a fire, overheating, or cause the
battery cells to rupture.
R
WARNING! NEVER
Iet fluid from inside the battery cells
come in contact with your body. If it does, immediately
wash with clean water.
CAUTION: DO NOT
continue to use the battery pack if
it emits an abnormal odor, heats up, or is discolored or
deformed. If any of these conditions occur, contact your
Icom dealer or distributor.
CAUTION: DO NOT
expose the battery pack to rain,
snow, saltwater, or any other liquids. Do not charge or use
a wet pack. If the pack gets wet, be sure to wipe it with a
clean dry cloth before using.
CAUTION: DO NOT
use the battery pack out of the
specified temperature range for the transceiver –25°C ~
+55°C (–13°F ~ +131°F): ETS version, –30°C ~ +60°C
(–22°F ~ +140°F): TIA version, and the battery itself –20°C
~ +60°C (–4°F ~ +140°F). Using the battery out of its
specified temperature range will reduce its performance
and battery cell’s life. Please note that the specified
temperature range of the battery may exceed that of the
transceiver. In such cases, the transceiver may not work
properly because it is out of its operating temperature
range.
CAUTION: DO NOT
leave the pack fully charged,
completely discharged, or in an excessive temperature
environment (above 50°C, 122°F) for an extended
period of time. If the battery pack must be left unused
for a long time, it must be detached from the transceiver
after discharging. You may use the battery pack until the
remaining capacity is about half, then keep it safely in a
cool and dry place at the following temperature range:
–20°C ~ +50°C (–4°F ~ +122°F) (within a month)
–20°C ~ +40°C (–4°F ~ +104°F) (within three months)
–20°C ~ +20°C (–4°F ~ +68°F) (within a year)
BE SURE
to replace the battery pack with a new one
approximately five years after manufacturing, even if it still
holds a charge. The material inside the battery cells will
become weak after a period of time, even with little use.
The estimated number of times you can charge the pack
is between 300 and 500. Even when the pack appears to
be fully charged, the operating time of the transceiver may
become short when:
• Approximately 5 years have passed since the pack was
manufactured.
•The pack has been repeatedly charged.
D
Charging caution
R
DANGER! NEVER
charge the battery pack in areas
with extremely high temperatures, such as near fires or
stoves, inside a sun-heated vehicle, or in direct sunlight.
In such environments, the safety/protection circuit in the
battery will activate, causing the battery to stop charging.
R
WARNING! NEVER
charge the transceiver during a
lightning storm. It may result in an electric shock, cause
a fire or damage the transceiver. Always disconnect the
power adapter before a storm.
R
WARNING! NEVER
charge or leave the battery in the
battery charger beyond the specified time for charging. If
the battery is not completely charged by the specified time,
stop charging and remove the battery from the battery
charger.
Continuing to charge the battery beyond the specified time
limit may cause a fire, overheating, or the battery may
rupture.
CAUTION: DO NOT
insert the transceiver (battery
attached to the transceiver) into the charger if it is wet or
soiled. This could corrode the battery charger terminals or
damage the charger. The charger is not waterproof.
CAUTION: DO NOT
charge the battery pack outside of the
specified temperature range: 10˚C to 40˚C (50˚F to 104˚F).
Icom recommends charging the pack at 25˚C (77˚F). The
pack may heat up or rupture if charged out of the specified
temperature range. Additionally, pack’s performance or
battery cell life may be reduced.
IMPORTANT
This instruction sheet includes some functions that are
usable only when they are preset by your dealer. The
transceiver may have other functions and operations that
are not described in this instruction sheet. Ask your dealer
for preset function details.
SAFETY TRAINING INFORMATION
Your Icom radio generates RF
electromagnetic energy while
transmitting. This radio is designed for
and classified as for “Occupational Use
Only.” This means it must be used only
during the course of employment by
individuals aware of the hazards, and the
ways to minimize such hazards. This
radio is NOT intended for use by the “General Population”
in an uncontrolled environment. This radio has been tested
and complies with the FCC and IC RF exposure limits for
“Occupational Use Only”. In addition, your Icom radio
complies with the following Standards and Guidelines with
regard to RF energy and electromagnetic energy levels
and evaluation of such levels for exposure to humans:
• FCC KDB Publication 447498 D03, Evaluating
Compliance with FCC Guidelines for Human Exposure
to Radio Frequency Electromagnetic Fields.
• American National Standards Institute (C95.1-1992),
IEEE Standard for Safety Levels with Respect to Human
Exposure to Radio Frequency Electromagnetic Fields, 3
kHz to 300 GHz.
• American National Standards Institute (C95.3-1992),
IEEE Recommended Practice for the Measurement of
Potentially Hazardous Electromagnetic Fields– RF and
Microwave.
• The antennas, batteries, belt clips, speaker-microphone,
and other accessories that are listed in “OPTIONS”
on this sheet, are authorized for use with this product.
Use of accessories other than those specified may
result in RF exposure levels exceeding the FCC and IC
requirements for wireless RF exposure.
• Health Canada Safety Code 6 - Limits of Human
Exposure to Electromagnetic Energy in the Frequency
Range from 3 kHz to 300 GHz.
To ensure that your expose to RF
electromagnetic energy is within the FCC
and IC allowable limits for occupational
use, always adhere to the following
guidelines:
•
DO NOT
operate the radio without a proper antenna
attached, as this may damage the radio and may also
cause you to exceed FCC and IC RF exposure limits. A
proper antenna is the antenna supplied with this radio by
the manufacturer or an antenna specifically authorized
by the manufacturer for use with this radio.
•
DO NOT
transmit for more than 50% of the total radio
use time (“50% duty cycle”). Transmitting more than
50% of the time can cause FCC and IC RF exposure
compliance requirements to be exceeded. The radio is
transmitting when the status indicator lights red. You can
cause the radio to transmit by pushing the “PTT” switch.
•
ALWAYS keep
the antenna at least 2.5 cm (1 inch)
away from the body when transmitting, and only use the
Icom belt-clips listed in “OPTIONS” on this sheet when
attaching the radio to your belt, or other place, to ensure
FCC and IC RF exposure compliance requirements are
not exceeded.
The information listed above provides t he user with
the information needed to make him or her aware of
RF exposure, and what to do to assure that this radio
operates within the FCC and IC RF exposure limits of
this radio.
•
Electromagnetic Interference/Compatibility
During transmissions, your Icom radio generates RF
energy that can possibly cause interference with other
devices or systems. To avoid such interference, turn off
the radio in areas where signs are posted to do so. DO
NOT operate the transmitter in areas that are sensitive
to electromagnetic radiation such as hospitals, aircraft,
and blasting sites.
•
Occupational/Controlled Use
The radio transmitter is used in situations in which
persons are exposed as a consequence of their
employment, provided those persons are fully aware of
the potential for exposure and can exercise control over
their exposure.
SUPPLIED ACCESSORIES
Battery pack
Belt clip
Battery charger
Power adapter
Flexible antenna
NOTE:
Some accessories are not supplied, or the shape
is different, depending on the transceiver version.
ABOUT CE AND DOC
Hereby, Icom Inc. declares that the versions
of IC-F1100D, IC-F1100DS, IC-F1100DT,
IC-F2100D, IC-F2100DS, and IC- F2100DT
which have the “CE” symbol on the product,
comply with the essential requirements of
the Radio Equipment Directive, 2014/53/EU, and the
restriction of the use of certain hazardous substances in
electrical and electronic equipment Directive, 2011/65/EU.
The full text of the EU declaration of conformity is available
at the following internet address:
http://www.icom.co.jp/world/support
D
Battery pack
Attaching:
1. Slide the battery pack in the direction of the arrow. (
1
)
2. Push the battery pack until the battery sliding locks
make a ‘click’ sound. (
2
)
q
w
q
Battery pack
Battery sliding locks
Detaching:
1. Push both battery sliding locks in the direction of the
arrow. (
z
)
•The battery pack is then released.
2. Lift up to detach the battery pack. (
x
)
z
z
x
D
Flexible antenna
Connect the antenna to the antenna connector.
CAUTION:
DO NOT carry the transceiver by holding only the
antenna.
•
DO NOT
connect an antenna other than those listed in
the “OPTIONS” section.
•Transmitting without an antenna may damage the
transceiver.
D
Belt clip
Attaching:
1. Remove the battery pack from the transceiver, if it is
attached.
2. Slide the belt clip in the direction of the arrow until the
belt clip is locked and makes a ‘click’ sound.
Belt clip
Detaching:
•Lift the tab up (
1
), and slide the belt clip in the direction
of the arrow (
2
).
2
1
BE CAREFUL! DO NOT
break your fingernail.
DISPOSAL
The crossed-out wheeled-bin symbol on your
product, literature, or packaging reminds you
that in the European Union, all electrical and
electronic products, batteries, and
accumulators (rechargeable batteries) must
be taken to designated collection locations at
the end of their working life. Do not dispose
of these products as unsorted municipal waste. Dispose of
them according to the laws in your area.
VOICE CODING TECHNOLOGY
The AMBE+2™ voice coding Technology embodied in this
product is protected by intellectual property rights including
patent rights, copyrights and trade secrets of Digital Voice
Systems, Inc. This voice coding Technology is licensed
solely for use within this Communications Equipment.
The user of this Technology is explicitly prohibited from
attempting to extract, remove, decompile, reverse
engineer, or disassemble the Object Code, or in any other
way convert the Object Code into a human-readable form.
U.S. Patent Nos.
#8,595,002, #8,359,197, #8,315,860, #8,200,497,
#7,970,606, #6,912,495 B2.
INSTRUCTIONS
Thank you for choosing this Icom product.
READ ALL INSTRUCTIONS
carefully and completely
before using this product.
VHF DIGITAL TRANSCEIVERS
iF1100D
series
UHF DIGITAL TRANSCEIVERS
iF2100D
series
A7456D-1EX-3
Printed in Japan
© 2018–2019 Icom Inc.
Jul. 2019
1-1-32 Kamiminami, Hirano-ku,
Osaka 547-0003, Japan