background image

ELECTRONIC CIRCULATOR FOR HEATING SYSTEMS - Art. P329

ICMA S.p.a. - Heating Technologies - www.icmaspa.it

FI.P329.EN.C  -  1 /2022

Icma SpA - Via Garavaglia, 4 - 20012 Cuggiono (MI) ITALY Tel: +39 02 97249134 - +39 02 97249135 - www.icmaspa.it - [email protected]

12

A LED provides information about the operation status of the circulator.

Selector

All settings are made using the selector on the housing front.
The selector can be adjusted in a continuous way with a rotation angle 

of 270 °.

The arrow on the selector indicates the operating mode chosen. 

LED light

The  LED  light  on  the  front  advises  the  commissioning/fault  of  the 

circulator.

Every  operating  mode  is  characterized  by  a  fixed  light  of  different 

colour.

After a change of operating mode, the LED pulses 5 times. The pulse 
will be a change of brightness intensity of the LED light.

6.2 Operating elements

6.3 Mode of operation

Fig. 6.1 Selector and LED light

LED

COLOR

DESCRIPTION

Green

P mode (Δp-v) – Proportional differential pressure

The circulator head is proportionally reduced with decreasing of the 
heat demand from the heating system (flow rate decrease) and is 
proportionally increased with increasing demand of the heat demand 
from the heating system (flow rate increase).

Blue

min-max mode – Fixed speed

The circulator maintains a fixed speed irrespectively of the heat demand 
from the heating system (flow rate).

The speed regulation is done by positioning the selector in a gradual 

manner at any point between the Min and Max positions.
Should this performance be insufficient, progressively increase the set 
value. Should this performance be excessive or should noise arise due to 
the speed of the pumped fluid, progressively reduce the calibration.

Flashing white

Automatic detection of the presence of air - Vent system.
Proceed with the vent routine

Red

Fault or malfunction
Faults, causes and remedies

Summary of Contents for P329

















Reviews: