background image

Service Fault Diagnosis

Type

Cause

Indicator

Action to Take

Bin Full

Storage bin is full of ice.

‘Full’ indicator light is on.

None 

Enjoy your ice!

Water Supply

Error

Water is not being supplied on time.

‘No Water’ indicator light is on.

Check water supply.

Check water reservoir is full.

Check operation of water level sensor.

Check operation of water dump valve.

Check water dump valve for leaks.

Evaporator Temp

Too High Error

Evaporator is not cold enough.

‘Temp’ indicator light flashes.

Check refrigerant charge (too low).

Check that compressor is running.

Check TXV operation.

Check S/L thermistor

Evaporator Temp

Too Low Error

Evaporator inlet temperature is too cold.

‘Temp’ & ‘Motor’ indicators flash 

simultaneously every 2 seconds.

Unplug & plug back in after 1 hour.

Check TXV operation.
Check L/L thermistor.

Check liquid-line solenoid valve.

Check motor/gear box operation.

Low Condenser

Temp Error

Ambient temp is lower than 33.8°F.

‘Temp’ indicator flashes every

4 seconds.

Raise ambient temperature above 

50°F.

High Condenser

Temp Error

Ambient temp is too high or condenser fails to cool

below 167°F.

‘Temp’ indicator light is on.

Lower ambient temperature.

Check air filter/condenser.

Check fan motor/blade.

Check fan cycle switch.

Check L/L thermistor

Locked Motor

Error

Motor is locked by foreign objects

‘Motor’ indicator light is on.

Unplug & plug back in after 1 hour.

Check motor/gearbox operation.

Check auger/agitator.

Check for ice jam.

Check for scale buildup.

S/L Thermistor

Error

Suction-line thermistor malfunctions.

‘Temp’ indicator light is on & ‘Motor’ 

indicator flashes.

Replace S/L thermistor.

L/L Thermistor

Error

Liquid-line thermistor malfunctions.

‘Temp’ indicator flashes & “Motor’ 

indicator light is on.

Replace L/L thermistor.

High Pressure

Error

Condenser fails to cool.

‘Temp’ and ‘Motor’ indicators lights 

are both on simultaneously.

Check refrigerant charge (too high).

Check air filter/condenser.

Check fan motor/blade.

Check high pressure switch.

Check fan cycling switch.

20

Summary of Contents for IM-770-AN





































Reviews: