background image

GB

3

LOCATE AND LEVELLING

This icemaker is designed to be installed in rooms
with temperatures between 10°C and 40°C.
Operating for long period out of these limits will
vaid your warranty program.     

Before installing the machine make sure that: 

The ambient temperature must not fall bellow 10°C
(50°F) or above 40°C (100°F).

The mains water temperature must not fall below
5°C (40°F) or above 40°C (100°F).

Machine is away from sources of heat and in a suf-
ficiently ventilated area; leave at least 8 inches (20
cms.) between the machine on the back and the
two sides and the wall.

Machine is correctly levelled in both the left to right
and front to rear directions by means of the
adjustable legs.

WATER SUPPLY CONNECTIONS

The mains water pressure must not fall below 1
atm. (14 Psi) or above 5 atms. (70 Psi). If pressure
is above 5 atms. a pressure regulator shoult be fit-

ted on the water supply machine.

Fix a flexibile palstic pipe (with an inside diameter
of 20 mm. and adequate lenght to reach and open
vented drain) to the waste pipe fitting. In the water
-cooled machine it must also be conected to the
second pipe fitting (that conveys water coming
from the condenser) to the drain.
Level of main drain must be sufficiently below ice-
maker waste outlets to ensure free flow of waste
water.
The drain recptacle should be an, open, trapped or
vented construction (see skech).

N.B. Make sure that water connection are made
before elettrical connections.

ELECTRICAL CONNECTIONS

Connect machine to water supply first and then to
eletricity supply.

Connect the machine to the eletricity supply after
having checked that the voltage corresponds to
that on the plate on the rear panel of the machine.

Connect the machine to the eletricity supply after
having checked that the voltage corresponds to
that on the plate on the rear panel of the machine.

INSTALLATION

WARNING This icemaker is not designed for outdoor installation and will not function in ambient temperatures
below 10°C (50°F) or above 40°C (100°C).
This icemaker will malfunction with water temperatures below 5°C (40°F) or above 40°C (100°C).

Summary of Contents for N140

























Reviews: