background image

IOD16022

Installation: General                                                                            IOD22030

Page 6

Final Preparation

Install the drain pan on the dispenser by engaging the slots in the metal backplate of the drain pan
onto the brackets protruding from the lower left and right hand corners of the dispenser front.  Push
down on the drain pan to lock it into place.

When applicable, seal the drain pan to the counter top.  If the dispenser is to be sealed to the counter
top, use the sealant recommended in the 

“Dispenser Installation”

 section of the instructions. 

 Place the cup rest into the drain pan.

Install the fluorescent bulb into the bulb holders located on the top sloped portion of the front of the
dispenser.

Place the merchandiser on the unit.

Sanitize the ice storage system. (See page 9)

Start-Up

Fill the bin with sanitary ice.

Place the cover on top of the dispenser.

Note:

This unit is provided with a timer that will activate the ice dispenser rotor for 1 to 6

seconds each time the unit is plugged into an electrical outlet and every 2 hours thereafter.
The agitation cycle helps to keep the ice from fusing together during long periods of non-use.
No ice is dispensed during the agitation.

Plug the unit’s power cord into the electrical outlet.  The rotor should turn for a few seconds and the
fluorescent bulb should illuminate.  Dispense several containers of ice.  

Check all connections including drain hoses for leaks.  Repair as required.

Summary of Contents for Counter Top Dispenser IOD22030























Reviews: