Iccons GT6-IXF User Manual Download Page 18

18

ICCONS® GAS TOOL GT6-IXF USER MANUAL

12  Warranty

ICCONS® Pty Ltd warrants the original purchaser of the GTIXF-160C against defective 
workmanship and faulty materials for 12 months from date of purchase.
It is a condition of the warranty period that;
•  Proof of original purchase and ownership, including address and phone number must be provided.
•  The GTIXF-160C has not been subjected to misuse, (beyond the recommendations or limitations 

specified and as outlined in the ICCONS® GTIXF-160C User manual), neglect or been damaged, 
modified or repaired without the approval of  ICCONS®.

•  The tool is presented on return in a condition that displays it has been cleaned and serviced as 

outlined in the ICCONS® GTIXF-160C User manual.

•  The Repairs to the tool are not required as a result of normal wear and tear (eg: Piston / Piston Rings ) 
WHERE LAWFUL, UNDER NO CIRCUMSTANCES SHALL ICCONS® PTY LTD BE LIABLE FOR 
INCIDENTAL, CONSEQUENTIAL, SPECIAL DAMAGES OR DIRECT OR INDIRECT LOSS OF ANY KIND, 
INCLUDING BUT NOT LIMITED TO BODILY INJURY, DEATH OR PROPERTY DAMAGE. ICCONS® 
ENTIRE LIABILITY IS LIMITED TO THE PURCHASE PRICE OF THIS PRODUCT.
If you wish to make a warranty claim, then the tool or part must be returned to ICCONS® Pty Ltd 
at the owner’s expense. ICCONS® will inspect the returned tool/parts, and at its own option may 
replace the tool/ parts and return it to the owner at its own cost if deemed to fall within the scope 
of the warranty conditions.

ICCONS® Pty Ltd cannot be held responsible for any repair other than those carried out by 

it or one of its Authorised Service Agents.

IMPORTANT NOTE FOR AUSTRALIAN CONSUMERS:
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably 
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to 
be of acceptable quality and the failure does not amount to a major failure.

PLEASE RETAIN A COPY OF THE TAX INVOICE FOR YOUR WARRANTY.

OWNERS COPY AND RECORD 

(original purchase receipt is still required for claims)

SERIAL No:

DATE PURCHASED:

DISTRIBUTOR / DEALERS NAME:

DEALER ADDRESS:

Summary of Contents for GT6-IXF





















Reviews: