background image

MARGIN

GUIDES

Stay within the yellow 

box. Do not let text go 

beyond, instead move 

to the next column or 

start a new page. 

9  

|  

www.icrealtime.com

Device does not 

operate properly/ lost 

password.

Please refer to section 2B for factory reset 

process. Cam will need to be Initialized after 

factory reset.

The water leakage.

The front or rear cap if damaged or removed 

can result in water leakage. The glass dome 

may also have been compromised from 

heavy strikes or heavy pressure. The 

waterproof plug of the rear cap may also 

have loosened.

IR video is poor/ does 

not turn on.

Verify the camera is supplied with the 

recommended amount of power. You may 

need to test voltage/  amperage of the 

camera while under load. Enough visible 

light at the location can also cause IRs to not 

switch on.

I can not upgrade the 

device via network.

Contact technical support to request 

firmware. 

I cannot login to the 

client-end or the 

WEB.

If the Camera HTTP port is changed, you will 

need to specify the port number after the IP. 

(ex: 

http://192.168.1.108:8080

) Ensure the 

correct login credentials are being used. The 

Smart ICRSS software will use the TCP port. 

Make sure you input the correct TCP port 

number.

The account is locked

Reboot the camera to clear lock out. Verify 

the login to make sure it is correct.

5A. FAQ

P2P status is “not 

connected/ offline”

You may need to set device IP to DHCP. 

After acquiring a different IP address, verify 

P2P status and set camera back to static IP 

if successful.

Camera does not 

show up on local 

network.

Verify the camera is supplied with the 

recommended power supply. Change 

network cable or use short patch cable to 

troubleshoot.

5B. APPENDIX TOXIC OR HAZARDOUS MATERIALS OR ELEMENTS

Component Name 

Pb

Hg

Cd

Cr VI

PBB

PBDE

Circuit Board 

Component

Device Case

Wire and Cable

Packing Components 

Accessories 

O: Indicates that the concentration of the hazardous substance in all 

homogeneous materials in the parts is below the relevant threshold 

of the SJ/T11363-2006 standard.

Summary of Contents for IPE1001











Reviews: