background image

                                                                           

 

 

12 

1  Appendix Toxic or Hazardous Materials or Elements 

Component Name 

Toxic or Hazardous Materials or Elements 

Pb 

Hg 

Cd 

Cr VI 

PBB 

PBDE 

Circuit Board Component 

○ 

○ 

○ 

○ 

○ 

○ 

Device Case 

○ 

○ 

○ 

○ 

○ 

○ 

Wire and Cable 

○ 

○ 

○ 

○ 

○ 

○ 

Packing Components 

○ 

○ 

○ 

○ 

○ 

○ 

Accessories 

○ 

○ 

○ 

○ 

○ 

○ 

O: Indicates that the concentration of the hazardous substance in all homogeneous materials in the 

parts is below the relevant threshold of the SJ/T11363-2006 standard. 

 

X: Indicates that the concentration of the hazardous substance of at least one of all homogeneous 

materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard. During the 

environmental-friendly use period (EFUP) period, the toxic or hazardous substance or elements 

contained in products will not leak or mutate so that the use of these (substances or elements) will not 

result in any severe environmental pollution, any bodily injury or damage to any assets.  The consumer 

is not authorized to process such kind of substances or elements, please return to the corresponding 

local authorities to process according to your local government statutes. 

 

Note 

 

This user’s manual is for reference only. Slight difference may be found in user 

interface. 

 

All  the  designs  and  software  here  are  subject  to  change  without  prior  written 

notice. 

 

All trademarks and registered trademarks mentioned are the properties of their 

respective  

owners. 

 

If there is any uncertainty or controversy, please refer to the final explanation of 

us. 

 

Please visit our website for more information. 

 
 

Summary of Contents for ICIP360L4


















Reviews: