background image

6-16

IBM Personal Computer User Guide

Advanced Setup

You can use these features to configure advanced hardware features. Do not 
attempt to change these settings unless you have an advanced technical knowledge 
of computer hardware. If these settings are configured incorrectly, the computer 
might not function correctly.

Cache Control

Use this setting to enable or disable the internal and external processor cache. 
Overall system performance improves when cache is enabled.

ROM Shadowing

Video BIOS Shadow

Use this setting to determine whether or not video BIOS will be copied to RAM. 
Video performance improves when Video BIOS Shadow is enabled.

Power Management Setup

The Power Management Setup allows you to configure your system to use the most 
effective method of saving energy, while operating in a manner consistent with your 
own style of computer use.

APM

Video Off Option

This setting determine the video off function for power management.

Enabled 

Video shadow is enabled

Disabled 

Video shadow is disabled

Always On

The video function is always on.

Suspend -> off

The video function is off when the system is in 
Suspend mode.

Susp, Stby -> off

The video function is off when the system is in 
Suspend or Stand by mode.

All Mode -> off

The video function is off in all modes.

Summary of Contents for Types 2193























































































































































































































Reviews: