background image

Notes:

1. In the ThinkPad Configuration program, the computer

can be set to suspend when docked.

2. The computer cannot enter hibernation mode when it

is attached to the ThinkPad Port Replicator with
Advanced Etherjet Feature.

Events that cause the computer to enter hibernation mode:

Ÿ

Hibernation mode requested by function key
(Fn+F12).

Ÿ

Timer conditions are satisfied in suspend mode when
hibernate by timer is enabled.

Ÿ

A critically low battery condition occurs.

Ÿ

The power switch is pressed. (BIOS Setup)

The compute exits hibernation mode and resumes opera-
tion when the power-on switch is pressed. When power is
turned on, the hibernation file in the boot record on the
hard disk drive is read and the system status is restored
from the hard disk drive.

The following events cause the computer to resume opera-
tion from hibernation mode.

Ÿ

The power switch is pressed.

Ÿ

The real time clock alarm is signaled.

Ÿ

Wake on LAN occurs.

How to Create the Hibernation Function:  

Do as

follows:

Ÿ

Turn off the computer.

Ÿ

Insert the hibernation utility diskette into the diskette
drive (you can create the diskette using the Diskette
Factory).

Ÿ

Turn on the computer.

Ÿ

Follow the instructions on the screen.

Note:  If you change the memory size, you need to

recreate the hibernation file or partition. For
partition-based hibernation, use the hibernation
utility to delete the partition first before creating a
new one.

 Symptom-to-FRU Index

The Symptom-to-FRU Index lists the symptoms and errors
and the possible causes. The most likely cause is listed
first.

Note:  Perform the FRU replacement or actions in the

sequence shown in the FRU/Action columns. If a
FRU replacement does not solve the problem, put
the original part back in the computer. Do not
replace a non-defective FRU.

   

ThinkPad 390/i Series 1700

33

Summary of Contents for ThinkPad 390






































































































Reviews: