IBM System Storage TS2900, Manual

Page: 65 / 130

Code (H) Description
Panel
Indication
Action Required
00B8
accessor error #1.
Reverse REV position (PP1) error (accessor
origin not detected or FWD position
detected). Suspect the P origin sensor, FWD
sensor, or P motor.
CHK 00B8 1. Check the accessor locking screw and remove it if it is installed. See Removing
the accessor locking screw .
2. Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library
operations resume. See
Running library verify test .
If the problem persists, see Contacting IBM technical support .
00B9 accessor error #2.
Forward FWD position (PP2) error (accessor
origin detected or FWD not detected).
Suspect the P origin sensor, FWD sensor, or P
motor. CHK 00B9
00BA accessor error #3.
PUT/GET/bar code reader position
(PP4/PP5/PPBF/PPBR) error (accessor origin
or FWD detected, or cell full). Suspect the P
origin sensor, FWD sensor, or P motor. CHK 00BA
00BC During initialization, the accessor origin is
not detected. Suspect the P origin sensor,
FWD sensor, or P motor. CHK 00BC
00BD During accessor movement, the movement
stop condition is detected. Suspect the P
encoder sensor or P motor. CHK 00BD
00BF No gap condition detected at the completion
of accessor operation. Suspect the centering
sensor, P origin sensor, FWD sensor, or P
motor. CHK 00BF
00C0 accessor operation disabled because a
cartridge magazine was removed. Suspect
the magazine set sensor. CHK 00C0 1. Confirm that the magazine is closed.
2. Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library
operations resume. See
Running library verify test .
If the problem persists, see Contacting IBM technical support .
00C8 Centering calibration error #1.
During centering calibration, centering
sensor OFF condition is not detected.
Suspect the centering sensor or P motor. CHK 00C8 Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library operations
resume. See
Running library verify test .
If the problem persists, see Contacting IBM technical support .
00C9 Centering calibration error #2.
During centering calibration, centering
sensor ON condition is not detected. Suspect
the centering sensor, X motor, or P motor. CHK 00C9
00D0 Checksum error detected during firmware
update. CHK 00D0 1. Confirm the firmware file version.
2. Reinstall the firmware file.
3. Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library
operations resume. See
Running library verify test .
If the problem persists, see Contacting IBM technical support .
00D1 Firmware ID error detected during firmware
update. CHK 00D1
00D2 Boot information error detected during
firmware update. CHK 00D2
00D3 Bar code reader is not in maintenance mode
during bar code reader firmware update
(operation interrupted). Suspect the bar code
reader cable connection. CHK 00D3 1. Initiate an inventory. See Table 2 .
2. Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library
operations resume. See
Running library verify test .
If the problem persists, see Contacting IBM technical support .
00D9 Magazine failed to unlock. Suspect the
magazine or magazine sensor. CHK 00D9 1. Cycle the power supply and try again.
2. Manually unlock the magazine, remove the magazine from the library, and
inspect it for damage.
If not damaged, return it to the library and run Library Verify before
normal library operations resume. See
Running library verify test .
If damaged, replace the magazine.
00DA I/O Station failed to unlock. Suspect the
magazine or magazine sensor. CHK 00DA
00DD An error detected during bar code reader
firmware check. Suspect the bar code reader
cable connection. CHK 00DD 1. Initiate an inventory. See Table 2 .
2. Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library
operations resume. See
Running library verify test .
If the problem persists, see Contacting IBM technical support .
00E0 Write operation not finished within 1 ms
when writing data to flash memory. CHK 00E0 Cycle the power supply and try again.
If the problem is corrected, run Library Verify before normal library operations
resume. See
Running library verify test .
If the problem persists, see Contacting IBM technical support .
00E1 Clear operation not finished within 10
seconds when clearing a sector in flash
memory. CHK 00E1
00E2 Error detected in tape library configuration
stored in flash memory. CHK 00E2
00E3 Checksum error detected in flash memory. CHK 00E3
60 TS2900 Tape Autoloader