manualshive.com logo in svg

IBM Power System 8247-21L, Installing

Share
Download
IBM Power System 8247-21L Installing Download Page 65

Warning:

This is a Class A product. In a domestic environment, this product may cause radio

interference, in which case the user may be required to take adequate measures.

VCCI Statement - Japan

The following is a summary of the VCCI Japanese statement in the box above:

This is a Class A product based on the standard of the VCCI Council. If this equipment is used in a
domestic environment, radio interference may occur, in which case, the user may be required to take
corrective actions.

Japan Electronics and Information Technology Industries Association Statement

This statement explains the Japan JIS C 61000-3-2 product wattage compliance.

This statement explains the Japan Electronics and Information Technology Industries Association (JEITA)
statement for products less than or equal to 20 A per phase.

This statement explains the JEITA statement for products greater than 20 A, single phase.

This statement explains the JEITA statement for products greater than 20 A per phase, three-phase.

Notices

49

Summary of Contents for Power System 8247-21L











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands