manualshive.com logo in svg

IBM Power System 8247-21L, Installing

Share
Download
IBM Power System 8247-21L Installing Download Page 17

Installing the IBM Power System S812L (8247-21L)

Use this information to learn about installing the IBM Power

®

System S812L (8247-21L) server.

Determining your server type

Determine whether you are installing a rack-mounted server or a server that arrived preinstalled in a
rack.

Determine which type of server you are installing. For more information, see the following table.

Table 1.

Server type

Description

Where to find related information

Rack-mounted

Your system arrived without a rack,
and you need to install the system
into an existing rack.

“Installing a rack-based server”

Water-cooled

Your water-cooled system arrived
without a rack, and you need to
install the system into an existing
rack that is water-cooled capable.

“Installing a rack-based water-cooled
server” on page 18

Preinstalled

Your system arrived preinstalled in a
rack.

“Setting up a preinstalled server” on
page 36

Installing a rack-based server

Use this information to learn about installing a rack-based 8247-21L server.

Prerequisite for installing the rack-mounted server

Use the information to understand the prerequisites that are required for installing the server.

You might need to read the following documents before you install the server:

v

The latest version of this document is maintained online. See Installing the IBM Power System S812L
(8247-21L) (http://publib.boulder.ibm.com/infocenter/systems/scope/hw/topic/p8egi/
p8egi_roadmap.htm).

v

To plan your server installation, see Planning for the system (http://www.ibm.com/support/
knowledgecenter/POWER8/p8had/p8had_8xx_kickoff.htm).

v

If you are using a Hardware Management Console (HMC), see Obtaining and applying machine code
updates for the HMC with an Internet connection (http://www.ibm.com/support/knowledgecenter/
POWER8/p8hai/area3fixeshmc.htm).

Consider the following prerequisites before you install the server:

1.

Ensure that you have the following items before you start your installation:

v

Phillips screwdriver

v

Flat-head screwdriver

v

Rack with two units of space

Note:

If you do not have a rack that is installed, install the rack. For instructions, see Racks and rack

features (http://www.ibm.com/support/knowledgecenter/POWER8/p8hbf/p8hbf_8xx_kickoff.htm).

2.

Ensure that you have one of the following consoles:

v

Hardware Management Console (HMC): Ensure that your HMC is at version 8 release 8.4.0 or later.

© Copyright IBM Corp. 2014, 2017

1

Summary of Contents for Power System 8247-21L











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands