background image

4405ch02 Architecture and technical overview.fm

Draft Document for Review May 28, 2009 1:59 pm

34

 

IBM Power 570 Technical Overview and Introduction

If the initial p5 570 server does not configure supported DDR2 memory, then the target 570 
can be configured with FC 5622 processor card and the desired amount of memory must be 
included in the model migration order.

Figure 2-7   Memory DIMM slots for FC 5621

A 570 with FC 5621 processor cards can be expanded by purchasing additional 570 
enclosures with FC 5622 processor cards. FC 5621 and FC 5622 cannot be mixed within the 
same 570 enclosure but can be mixed in the same system. Maximum memory configurable 
depends from the number of FC 5621 and FC 5622 processor cards available in the fully 
combined 570 system.

2.4.4  OEM memory

OEM memory is not supported or certified for use in IBM System p servers. If the 570 is 
populated with OEM memory, you could experience unexpected and unpredictable behavior, 
especially when the system is using Micro-Partitioning technology.

All IBM memory is identified by an IBM logo and a white label that is printed with a barcode 
and an alphanumeric string, as illustrated in Figure 2-8 on page 35.

Important:

 The process to migrate a p5 570 to a 570 requires analysis of the existing 

p5 570 memory DIMMs. Contact an IBM service representative before issuing the 
configuration upgrade order.

J1D

J0D

J0C

J1C

J1A

J0A

J0B

J1B

POWER6

chip

L3 cache

Memory buffer 

chip

D

Memory buffer 

chip

A

Memory buffer 

chip

C

Memory buffer 

chip

B

Summary of Contents for Power 570















































































































































Reviews: