
3.
Install the bezel assembly (see “Installing the bezel assembly” on page 40).
4.
Install the optional expansion unit, if you removed one from the blade server to
replace the microprocessor and heat sink (see “Installing an optional expansion
unit” on page 38).
5.
Install the blade server cover (see “Installing the blade server cover” on page
36).
6.
Install the blade server into the BladeCenter unit (see “Installing the blade
server in a BladeCenter unit” on page 34).
Removing the system-board assembly
Use this information to remove the system-board assembly from the blade server.
Attention:
The system-board assembly is a field-replaceable unit (FRU) and must
be replaced by a trained service technician. To contact an IBM service
representative, see “Hardware service and support” on page 177.
When you replace the system board, you will replace the system board and blade
base as one assembly. After replacement, you must either update the blade server
with the latest firmware or restore the pre-existing firmware that the customer
provides on a diskette or CD image.
Note:
See “System-board layouts” on page 10 for more information on the
locations of the connectors, jumpers and LEDs on the system board.
To remove the system-board assembly, complete the following steps:
1.
Before you begin, read “Safety” on page v and “Installation guidelines” on
page 31.
2.
If the blade server is installed in a BladeCenter unit, remove it (see “Removing
the blade server from the BladeCenter unit” on page 33 for instructions).
3.
Carefully lay the blade server on a flat, static-protective surface.
4.
Remove the blade server cover (see “Removing the blade server cover” on page
35).
5.
If an optional expansion unit is installed, remove the expansion unit (see
“Removing an optional expansion unit” on page 37).
6.
Remove the blade server bezel assembly (see “Removing the bezel assembly”
on page 39).
7.
Remove all of the installed components in the following list from the
system-board assembly; then, place them on a static-protective surface or install
them on the new system-board assembly.
v
cKVM card. See “Removing a concurrent KVM card” on page 48.
v
DIMMs. See “Removing a memory module” on page 44.
v
I/O expansion card. See “Removing an I/O expansion card” on page 50,
“Removing a storage interface card” on page 53, and “Removing a
high-speed expansion card” on page 55.
v
Microprocessors and heat sinks. See “Removing a microprocessor and heat
sink” on page 60.
v
Storage drives. See “Removing a hot-swap storage drive” on page 43 or
“Removing a fixed-storage drive” on page 41.
8.
If you are instructed to return the system-board assembly, follow all packaging
instructions, and use any packaging materials for shipping that are supplied to
you.
Chapter 5. Removing and replacing blade server components
65
Summary of Contents for HS12 - BladeCenter - 8028
