IBM FC EJ08 Manual Download Page 3

Page: 3 / 66

Contents

Safety notices........................................................................................................v

Installing PCIe adapters in the system...................................................................1

Preparing the 9080-M9S system to install a PCIe adapter........................................................................ 1

Installing a PCIe adapter in the system...................................................................................................... 8

Preparing the 9080-M9S system for operation after installing a PCIe adapter ..................................... 17

Related procedures for installing PCIe adapters......................................................................................22

Avoiding electric shock........................................................................................................................ 22

Handling static-sensitive devices........................................................................................................ 23

Updating the worldwide port name..................................................................................................... 23

Removing and replacing the tailstock on a PCIe adapter .................................................................. 24

PCIe hot-plug manager access for AIX............................................................................................... 29

Installing the AIX device driver software............................................................................................ 31

Installing or replacing a PCIe adapter with the system power turned on in a Virtual I/O Server......33

Verifying that the hot-plug PCI tools are installed for Linux...............................................................36

Checking the amount of remaining life in NVMe devices....................................................................37

Notices................................................................................................................41

Accessibility features for IBM Power Systems servers............................................................................ 42

Privacy policy considerations ................................................................................................................... 43

Trademarks................................................................................................................................................ 43

Electronic emission notices.......................................................................................................................43

Class A Notices.....................................................................................................................................43

Class B Notices.....................................................................................................................................47

Terms and conditions................................................................................................................................ 49

iii

Summary of Contents for FC EJ08



































































Search results

Summary of Contents for FC EJ08

Reviews:

Related manuals for FC EJ08

Brands by name

Popular brands

IBM FC EJ08, Manual

Search results

Summary of Contents for FC EJ08

Reviews:

Related manuals for FC EJ08

Brands by name

Popular brands