IBM DJSA-210 - Travelstar 10 GB Hard Drive, Specifications

Share

195 pages before
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211

Page: 210 / 211

background image

© International Business Machines Corporation 2001
www.ibm.com/harddrive

IBM Technology Group Support Center
Telephone: 888.IBM.5214 or 507.286-5825
Fax: 507.253.DRIVE
E-mail: [email protected]

Singapore Technical Support Center
Telephone: (65)6418.9595 or 1800.418.9595
E-mail: [email protected]

UK Technology Group Support Center
Telephone: 44.1475.898.125
E-mail: [email protected]

Germany Technology Group Support Center
Telephone: 49.7032.153050
E-mail: [email protected]

IBM Storage Technology Division
5600 Cottle Road
San Jose, CA 95193
www.ibm.com/storage

Printed in the United States of America
12-2001
All Rights Reserved

IBM is a registered trademark of International Business Machines
Corporation. Other company, product, and service names may be
trademarks or service marks of others.

Product description data represents IBM’s design objectives and is
provided for comparative purposes; actual results may vary depending
on a variety of factors. Product claims are true as of the date of the
first printing. This product data does not constitute a warranty.
Questions regarding IBM’s warranty terms or the methodology used to
derive this data should be referred to an IBM representative. Data
subject to change without notice.

References in this publication to IBM products, programs, or services
do not imply that IBM intends to make them available in all countries
in which IBM operates.

Document #S07N-3499-05
Publication #1520

®

«
...
208
209
210
211
»

Summary of Contents for DJSA-210 - Travelstar 10 GB Hard Drive




















































































































































































































Reviews:

No comments

Related manuals for DJSA-210 - Travelstar 10 GB Hard Drive

Brand: WATSON Pages: 12

Brand: Euromate Pages: 23

Brand: IBM Pages: 2

Brand: Sans Digital Pages: 2

Brand: LaCie Pages: 54

Brand: StarTech.com Pages: 7

ReadyNAS 3220 Series

Brand: NETGEAR Pages: 4

Brand: Dancover Pages: 66

Brand: Husky Pages: 7

Brand: Netstor Pages: 17

XCubeNAS XN5016R

Brand: Qsan Pages: 64

Brand: Yardmaster Pages: 28

StorageScaler 2460

Brand: DataDirect Networks Pages: 46

Brand: DataDirect Networks Pages: 106

Universal Bench

Brand: Kreg Pages: 12

Brand: Seagate Pages: 2

Garage Workshop T3

Brand: Stanley Pages: 16

Brand: FUM Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands