•
Relative humidity: 20 to 80 percent (non-condensing),
23
°
C (73
°
F) wet bulb operating
•
Electrical voltage: 100 to 127 or 200 to 240 V ac, 50-60
Hz, Autoranging
•
Electrical power: 0.047 kVA
•
Noise level: 5.3 bels idle, 5.5 bels operating dBa
•
Leakage and starting current:
3.5 mA at 240
V ac/50 Hz
•
Inrush current:
60 amperes peak (a ten amp fuse is
sufficient for overload protection)
Note:
Values shown are the maximum levels with two
feature numbers 1100 installed.
Other combinations of
drive or panel features result in lower values.
Hardware requirements:
The Half-High LTO-2 Tape Drive
(#1109) may be installed in either bay of the 7212
Model 102 Storage Device Enclosure.
For additional
details, refer to Hardware Announcement 101-292, dated
October 2, 2001.
IBM
pSeries
and p5 support of the 7212
Model 102
The drive features of the 7212 Model 102 can be attached
to pSeries or RS/6000
servers as listed below.
Appropriate small computer system interface (SCSI)
cables must be specified on the initial order. For cabling
information refer to the
Cable orders
section of this
announcement.
The drive features of the 7212 Model 102 are supported
for attachment to the PCI Dual Channel Ultra3 SCSI
Adapter (#6203).
This adapter is used in the following
pSeries and RS/6000 systems:
•
7017
—
S80
•
pSeries 680 (7017
—
S85)
•
pSeries 620 (7025
—
6F0, 6F1)
•
7025
—
F50, F80, H70
•
pSeries 660 (7026
—
6H0, 6H1, 6M1)
•
pSeries 640 (7026
—
B80)
•
7026
—
H70, H80, M80
•
pSeries 610 (7028
—
6C1, 6E1)
•
pSeries 630 (7028
—
6C4, 6E4)
•
pSeries 670 (7040-671) through the (7040-61D) I/O
drawer
•
pSeries 690 (7040-681) through the (7040-61D) I/O
drawer
•
7043
—
150, 270
•
7044
—
170, 270
•
7046
—
B50
•
9112-265
•
9114-275
•
9117-570
The drive features of the 7212 Model 102 are supported
for attachment to the PCI Ultra-2 SCSI LVD (low voltage
differential or single-ended) 64-bit Adapter (#6205) on the
following pSeries and RS/6000 systems:
•
7017
—
S80
•
pSeries 680 (7017
—
S85)
•
pSeries 620 (7025
—
6F0, 6F1)
•
7025
—
F50, F80, H70
•
pSeries 660 (7026
—
6H0, 6H1, 6M1)
•
pSeries 640 (7026
—
B80)
•
7026
—
H70, H80, M80
•
7044
—
170, 270
•
7046
—
B50
The drive features of the 7212 Model 102 are supported
for attachment to the PCI Single-Ended Ultra SCSI
Adapter (#6206).
This adapter is used in the following
pSeries and RS/6000 models:
•
7017
—
S80
•
pSeries 680 (7017
—
S85)
•
pSeries 620 (7025
—
6F0, 6F1)
•
7025
—
F50, F80, H70
•
pSeries 640 (7026
—
B80)
•
7026
—
H70, H80
•
pSeries 610 (7028-6C1), pSeries 610 (7028-6E1)
•
pSeries 670 (7040-671) through the (7040-61D) I/O
drawer
•
pSeries 690 (7040-681) through the (7040-61D) I/O
drawer
•
7043
—
150, 270
•
7044
—
170, 270
•
7046-B50
•
9112-265
The drive features of the 7212 Model 102 are supported
for attachment to the Integrated Ultra2 SCSI Adapter
(LVD with VHDCI connector). This adapter is used in the
following pSeries and RS/6000 models:
•
pSeries 620 (7025
—
6F0, 6F1)
•
7025
—
F80
•
pSeries 660 (7026
—
6H0, 6H1, 6M1)
•
pSeries 640 (7026
—
B80)
•
7026
—
H70, H80, M80
•
7044
—
170, 270
The drive features of the 7212 Model 102 are supported
for attachment to the Integrated Ultra3 SCSI Adapter
(LVD with VHDCI connector). This adapter is used in the
following pSeries models:
•
pSeries 610 (7028
—
6C1, 6E1)
•
pSeries 630 (7028
—
6C4, 6E4)
•
9112-265
•
7038-6M2 (P650)
The drive features of the 7212 Model 102 are supported
for attachment to the PCI SCSI-2 Fast/Wide Single-Ended
Adapter (#6208) on the following pSeries systems:
•
7017-S80
•
7025-F50, 7025-F80, 7025-H70
•
7026-H70
The drive features of the 7212 Model 102 are supported
for attachment to the PCI-X Dual Channel ULTRA320 SCSI
RAID Adapter (#5703).
This adapter is used in the
following pSeries models:
•
pSeries 610 (7028-6C1, 6E1)
•
pSeries 630 (7028-6C4, 6E4) through the 7311-D20 I/O
Drawer
•
pSeries 615 (7029-6C3, 6E3)
105-397
-2-
