IBM 7208-341 Setup And Operator Manual Download Page 62

Page: 62 / 66

¦ C8 ¦ A backup positioning command is ¦ 2 ¦ - ¦

¦ ¦ required ¦ ¦ ¦

+-----------+------------------------------------+-----------+-----------¦

¦ C9 ¦ Command requires a tape and none ¦ 7.3 ¦ - ¦

¦ ¦ is loaded ¦ ¦ ¦

+-----------+------------------------------------+-----------+-----------¦

¦ CA ¦ Log Threshold met ¦ 3 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ CB ¦ Log Parameter changed ¦ 3 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ CC ¦ Parameter List Length error in CDB ¦ 2 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ CD ¦ Illegal Operation Code ¦ 2 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ CE ¦ Invalid field or reserved bits set ¦ 2 ¦ - ¦

¦ ¦ in CDB ¦ ¦ ¦

+-----------+------------------------------------+-----------+-----------¦

¦ CF ¦ This LUN is not supported ¦ 2 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ D0 ¦ Invalid field in Parameter List ¦ 2 ¦ - ¦

¦ ¦ (Mode Data) ¦ ¦ ¦

+-----------+------------------------------------+-----------+-----------¦

¦ D1 ¦ Illegal bit set in identify ¦ 2 ¦ - ¦

¦ ¦ message ¦ ¦ ¦

+-----------+------------------------------------+-----------+-----------¦

¦ D2 ¦ Media removal is prevented ¦ 2 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ D3 ¦ Command has mode mismatch ¦ 2 ¦ - ¦

¦ ¦ (variable/fixed) ¦ ¦ ¦

+-----------+------------------------------------+-----------+-----------¦

¦ D4 ¦ Illegal Transfer Length in CDB ¦ 2 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ D6 ¦ Tried to change Mode Parms and not ¦ 2 ¦ - ¦

¦ ¦ at LBOT ¦ ¦ ¦

+-----------+------------------------------------+-----------+-----------¦

¦ D7 ¦ Can't read medium incompatible ¦ 14 ¦ - ¦

¦ ¦ format ¦ ¦ ¦

+-----------+------------------------------------+-----------+-----------¦

¦ D8 ¦ Overlapped commands attempted bad ¦ 2 ¦ - ¦

¦ ¦ ITL nexus ¦ ¦ ¦

+-----------+------------------------------------+-----------+-----------¦

¦ DA ¦ Illegal bits set in ID message ¦ 2 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ DB ¦ Cannot write to tape not AME ¦ 14 ¦ T = 100% ¦

+-----------+------------------------------------+-----------+-----------¦

¦ DC ¦ Rounding has occurred ¦ 10 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ DD ¦ Not ready - head synch tape ¦ 7 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ DE ¦ Density not supported ¦ 2 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ E0 ¦ Aborted in CDB phase, parity or ¦ 12 ¦ - ¦

¦ ¦ other error ¦ ¦ ¦

+-----------+------------------------------------+-----------+-----------¦

¦ E1 ¦ Aborted prior to Data phase, bad ¦ 12 ¦ - ¦

¦ ¦ message ¦ ¦ ¦

+-----------+------------------------------------+-----------+-----------¦

¦ E2 ¦ Aborted in Data phase, init ¦ 12 ¦ - ¦

¦ ¦ detected error ¦ ¦ ¦

+-----------+------------------------------------+-----------+-----------¦

¦ E3 ¦ Aborted in Data phase, bad message ¦ 12 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ E4 ¦ Aborted after Data phase, bad ¦ 12 ¦ - ¦

¦ ¦ message ¦ ¦ ¦

+-----------+------------------------------------+-----------+-----------¦

¦ E5 ¦ Aborted after Data phase, other ¦ 12 ¦ - ¦

¦ ¦ error ¦ ¦ ¦

+-----------+------------------------------------+-----------+-----------¦

¦ E6 ¦ ABORT caused by SCSI Bus Parity ¦ 12 ¦ - ¦

¦ ¦ Error ¦ ¦ ¦

+-----------+------------------------------------+-----------+-----------¦

¦ E7 ¦ ABORT sent by initiator has been ¦ 12 ¦ - ¦

¦ ¦ completed ¦ ¦ ¦

+-----------+------------------------------------+-----------+-----------¦

¦ E8 ¦ Drive needs cleaning ¦ 1 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ EA ¦ Invalid mode (2.3GB) for data ¦ 2 ¦ - ¦

¦ ¦ compression ¦ ¦ ¦

+-----------+------------------------------------+-----------+-----------¦

¦ EB ¦ Download in progress ¦ 3 ¦ - ¦

+-----------+------------------------------------+-----------+-----------¦

¦ EC ¦ Log parameter overflow (recovered ¦ 10 ¦ - ¦

¦ ¦ error) ¦ ¦ ¦

+-----------+------------------------------------+-----------+-----------¦

7208 Model 341 Setup and Operator Guide

Appendix B. Fault Symptom Codes and Error Recovery Procedure Numbers

¦ Copyright IBM Corp. 1997

B.0 - 4

Summary of Contents for 7208-341



































































Search results

Summary of Contents for 7208-341

Reviews:

Related manuals for 7208-341

Brands by name

Popular brands

IBM 7208-341, Setup And Operator Manual

Search results

Summary of Contents for 7208-341

Reviews:

Related manuals for 7208-341

Brands by name

Popular brands