background image

19

18

Mojo Hd3 / Mojo 3

Dropper Cable Routing

Mojo Hd3 / Mojo 3

Derailleur Cable Routing

a note on  

reverB droPPer routIng

The Reverb dropper routing we prefer is not 
illustrated, but we’ll describe it for you. you 
need three of our hydro cable stops. Route the 
Reverb into the left side of the down tube (it’s a 
single port) using our hydro port. Use two other 
hydro ports at the bottom left side of the down 
tube and seattube, and fish the dropper tubing 
through to the seattube. Connect as normal.
If you’re using Shimano’s new side pull front 
derailleur, route it through the drive side of the 
down tube and then out at the bottom of the 
drive side. For top mount front derailleurs use 
the toptube for entry and exit for the derailleur 
cable. Note that you have the choice of full 
housing or interrupted derailleur housing with 
our versatile port configurations.
For droppers that use cable and housing, such 
as the kS LEV, route the housing according to 
the illustrations.

BIKe set-uP tIPs and trIcKs

BIKe set-uP tIPs and trIcKs

a note on Mojo Hd3 / Mojo 3 

routIng WItH toP Pull deraIlleurs

 

We have made the Mojo HD3 and Mojo 3 compatible 
with the new Shimano side swing front derailleurs. 
Should you be retrofitting an older style top pull 
derailleur refer to new Ripley Routing on 

page 14.

BU

IL

D

BU
IL

D

Summary of Contents for New Ripley







































Reviews: