background image

AST1029MP-960

 

Page 16 

20/11/2006

 

 

 

 
 
Installation 

  

All plumbing and electrical connections must conform 
to local codes. Inspect the unit carefully for carrier 
shortage or shipping damage. 
 

Location Selection 

 

 

Locate unit as close to a drain as possible 

 

If supplementary water treating equipment is 
required, make sure that adequate additional 
space is available. Locate the brine tank in an 
accessible place so that salt can easily be added. 

 

Do not install any unit closer than 10ft (3m) of 
piping between the outlet of the water conditioner 
and the inlet of the water heater. Water heaters 
can transmit heat back down the cold water pipe 
into the control valve. Hot water can severely 
damage the controller. 

 
A 10ft (3m) total pipe run (including bends, elbows 
etc) is a reasonable distance to prevent hot water 
damage. A positive way to prevent hot water from 
flowing from a heat source to the conditioner is to 
install a check valve in the soft water piping from the 
conditioner. If a check valve is installed, make sure 
that the water-heating unit is equipped with a properly 
rated temperature and pressure safety relief valve. 
Always conform to local codes. 
 

 

Do not locate the unit in an area where the temp 
ever falls below 34ºF (1ºC) or over 120ºF (49ºC). 

 

Do not install the unit near acid or acid fumes. 

 

Do not expose the unit to petroleum products. 

 
Water Line Connection 

 

A bypass valve system must be installed to provide 
for occasions when the water conditioner must is by- 
passed for hard water or for servicing. The most 
common bypass systems are the Autotrol Series 156 
Bypass Valve, Figure 3, and plumbed-in globe 
valves, Figure 4. Though both are similar in function, 
the Autotrol Bypass offers simplicity and ease of 
operation. 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Drain Line Connection 

 
The ideal location for the unit is above and not more 
than 20ft (6.1m) from the drain. For such installations, 
using the appropriate adaptor fitting (not supplied), 
connect 1/2 in (1.3cm) plastic tubing to the drain line 
connection located at the rear of the control. 
 
 
 
 
 
 
 
 
 
 
 
 
If the unit is located more than 20ft (6.1m) from the 
drain, use 3/4in (1.9cm) tubing for runs up to 40ft 
(12.2m). You may elevate the line up to 6ft (1.8m) 
providing the run does not exceed 15ft (4.6m) and the 
water pressure at the conditioner is not less than 
40psi (280kPa). You may elevate an additional 2ft 
(61cm) for each additional 10psi (70kPa) of water 
pressure.  
 
When the drain line is elevated and empties into a 
drain which is below the level of the control valve, 
form a 7 inch (17cm) loop at the drain end of the line 
so that the bottom of the loop is level with the drain 
line connection. This provides an adequate siphon 
trap.  
 
If the drain empties into an overhead sewer line, a 
sink-type trap must be used. 
 

 

 

 

Not In Bypass 

In Bypass 

Not In Bypass

 

In Bypass

 

Figure 3 - Autotrol Series 156 Bypass Valve 

Figure 4 - Typical Globe Valve Bypass 
System

 

Figure 5 - Air Gap Installation 

Summary of Contents for AST1029MP-960


































Reviews: