background image

AS1375MP-960

 

Page 18 

20/11/2006

 

 

 

When the green light is on next to the TIME OF DAY 
legend, the display is showing the time that the 
control thinks it is correct. If you need to change the 
Time of Day, refer to the instructions later in this 
section. The Time of Day displays time in hours and 
minutes sepa-rated by a colon[:]. When the colon is 
flashing on and off, water is flowing through the 
conditioner. There is a small red dot in the upper left 
corner near the PM letters to indicate PM for 12-hour 
clocks. When the dot is off, the time is AM. You can 
set the clock for any time, AM or PM. 

  

Complete the following steps to change the Time of 
Day: 
1.  Press the down arrow 

ò

 button until the green 

light next to the TIME OF DAY legend is on. 

2.  Press the 

SET

 button and the minute number on 

the display starts flashing. If you want to change 
this number , press the up arrow 

ñ

 button to 

increase the number or the down arrow 

ò

 button 

to decrease the number. To skip the number 
without changing, press the left arrow 

ï

 button. 

3.  When the number is correct, press the left arrow 

ï

 button. The first number stops and the next 

number starts flashing. You can only change the 
flashing number. 

4.  Continue changing numbers until you reach the 

desired setting. 

5.  Press the 

SET

 button. The number stops flashing 

and the control accepts the new setting. After 
approximately 30 seconds, the control starts alter-
nating the display between TIME OF DAY and 
CAPACITY. 

Note: 

If a beep sounds, the new setting is not 

accepted. 
 

Reminder: 

The control does not keep time during a 

power outage but will resume its timekeeping from the 
time of day power was lost. A short power outage 
should not cause a problem. If the outage is several 
hours, the control will regenerate at the wrong time of 
day. All other memory is stored in the NOVRAM and 
maintained during power outage. Refer to page3. 
 

Time of Regeneration 

 
The control uses the Time of Regeneration to decide 
when to begin a regeneration. When a regeneration is 
necessary and the Time of Day Clock is at the same 
time as the Time of Regeneration setting, the control 
starts the regeneration. The factory setting for Time of 
Regeneration is 2:00 AM. If this time is inconvenient, 
you can select any other time of day. Remember that 
the soft water is not available during a regeneration of 
the water conditioner. Time of Regeneration can be 
set for any time, AM or PM. 
 

Note: 

The control may be programmed for an immed-

iate regeneration option. In this case, the control does 
not wait for the Time of Regeneration but regenerates 

when the remaining capacity reaches zero. Contact 
your dealer for more information regarding this option. 
 
Complete the following steps to change the Time of 
Regeneration: 
1.  Press the down arrow 

ò

button until the green 

light next to the TIME OF REGEN legend is on. 

2.  Press the 

SET 

button and the minute number on 

the display starts flashing. If you want to change 
this number, press the up 

ñ

 button to increase 

the number or the down arrow 

ò

 button to 

decrease the number. 
To skip the number without changing, press the 
left arrow 

ï

 button. 

3.  When the number is correct, press the left arrow 

ï

 button. The first number stops flashing and the 

next number starts flashing. You can only change 
the flashing number. 

4.  Continue changing numbers until you reach the 

desired setting. 

5.  Press the 

SET

 button. The number stops flashing 

and the control accepts the new setting. After 
approximately 30 seconds, the control starts alter-
nating the display between TIME OF DAY and 
CAPACITY. 

Note: 

If a beep sounds, the new setting is not 

accepted. 
 

Hardness Setting  

 
The Hardness Setting refers to the amount of hard-
ness

 

minerals in your water before it is conditioned. 

The control uses this setting to calculate how many 
gallons of water can be conditioned before a 
regeneration is necessary. 
Your water treatment dealer tested the water at the 
time of installation and entered a Hardness Setting in 
the control. We recommend that you consult your 
dealer or have your water retested before changing 
this setting 
You can see the Hardness Setting the dealer entered 
by pressing the down arrow 

ò

 button until the green 

light next to the HARDNESS legend is on. The 
number on the display is the measure of water 
hardness in grains per gallon (milligrams per litre for 
metric). 
 
Complete the following steps to change the Hardness 
Setting: 
1.  Press the down arrow 

ò

button until the green 

light next to the HARDNESS legend is on. The 
setting range is (30 TO 2500 milligrams/litre for 
metric) 

2.  Press the 

SET 

button and the minute number on 

the display starts flashing. If you want to change 
this number, press the up 

ñ

 button to increase 

the number or the down arrow 

ò

 button to 

decrease the number. 
To skip the number without changing, press the 
left arrow 

ï

 button. 

Summary of Contents for AS1375MP-960


































Reviews: