IAC INDUSTRIES SMS S1 SMART MOBILE STATION Assembly Instructions Manual Download Page 67

Page: 67 / 68

There are two CPU Holder Brackets (item S) in Hardware

Kit HWR521. the Brackets mount to both sides of the
upright. Install the square head bolts (item P), hex nuts
(item R), and washers (item Q) as shown at left.

Do not tighten this hardware.

Attach the CPU Holder Brackets to the Upright (see

below). Set at the desired height. Tighten the nuts.

Remove the Bottom Pan from the CPU Holder Assembly.

Attach the top portion of the CPU Holder Assembly to
the brackets mounted to the upright using 1/4-20 x .625

Philllips head screws (item N). Re-install the Bottom
Pan.

Bottom

Pan

SMS S8 CPU Holder Assembly

Summary of Contents for SMS S1 SMART MOBILE STATION





































































Search results

Summary of Contents for SMS S1 SMART MOBILE STATION

Reviews:

Related manuals for SMS S1 SMART MOBILE STATION

Brands by name

Popular brands

IAC INDUSTRIES SMS S1 SMART MOBILE STATION, Assembly Instructions Manual

Search results

Summary of Contents for SMS S1 SMART MOBILE STATION

Reviews:

Related manuals for SMS S1 SMART MOBILE STATION

Brands by name

Popular brands