i3 International Am57, User Manual

Page: 3 / 5

USER MANUAL
Page -2- Page -3-
Am57 Analog Dome Camera
ADJUST ZOOM/FOCUS via VIDEO PILOT CLIENT
(incl. SRX-PRO v7 and up)
1.
Set the PTZ Protocol of the Am57 to
i3-HDA
in the HR16/
HR16v2 encoder (Steps 1-5 of the ADJUST ZOOM/FOCUS via
HR16/HR16v2)
2.
Add HR16/HR16v2 to SRX-Pro and enable PTZ control for Am57
input. Follow the instructions in the relevant section depending
on SRX-Pro version.
3.
Connect to the remote SRX-Pro Server with VPC.
4.
Double-click on the Am57 camera to bring it into full single-
channel division.
5.
Click
PTZ > Advanced
in the on-screen menu.
6.
Use the on-screen Zoom In/Out controls and
Focus In/Out controls in the PTZ Advanced Options side panel to adjust Zoom and
Focus until the desired view is achieved.
ADJUST ZOOM/FOCUS via VEO16p (LOCAL)
1. Connect Am57 to Veo16p BNC output.
2. Log into your Veo16p (Default: ADMIN/1234).
3.
Go to
MENU > SYSTEM SETUP > CAMERA > PTZ
SETUP
4. In PROTOCOL drop down menu, select COAXITRON for
all Am57 cameras. Click APPLY , then CLOSE .
5.
On the Veo16p Live screen, click the PTZ button to
display PTZ control panel.
6. Use the ZOOM and FOCUS icons adjust Zoom and Focus until the desired view is
achieved.
ADJUST ZOOM/FOCUS via VEO16p (REMOTE)
1. Repeat Steps 1-4 of the ADJUST ZOOM/FOCUS via VEO16p
(LOCAL) section.
2.
Connect your Veo16p to the network using the ETHERNET
port on the rear panel. Follow Veo16p manual for more
instructions.
3.
On the remote PC, open Internet Explorer and enter the IP
address of your Veo16p in the address bar, followed by the
Web Service Port. Default service port: 8080 .
(E.g. http://192.168.0.59:8080 )
4.
Enter user credentials in the login screen.
(Default: ADMIN/1234).
5. Install ActiveX, as required.
6. In the Veo16p Live screen mode, double-click on the Am57
camera to bring it into full single-channel division.
7.
Click on the PTZ tab and use Use the ZOOM and FOCUS icons adjust Zoom and Focus
until the desired view is achieved.
CALLING UP OSD MENU
Camera’s OSD menu can be accessed through i3’s encoder, i3’s standalone HVR’s local or
remote interfaces or through SRX-Pro/VPC interface.
In all cases,
Iris Open
icon in the Live Mode PTZ panel will
bring up the camera’s on screen display.
PTZ panel OSD Menu control buttons:
Iris Open
- Bring up the OSD, confirm menu selection/enter
sub-menu.
UP/DOWN arrows
to navigate within camera menus.
LEFT/RIGHT arrows
to adjust value of the selected item.
CALLING UP OSD via HR16/HR16v2
1.
Repeat Steps 1-8 of the ADJUST ZOOM/FOCUS via
HR16/HR16v2 section.
2.
Use the
Iris Open
and
UP/DOWN/LEFT/RIGHT
buttons
on the PTZ Control panel to bring up and navigate in the
OSD menus.
CALLING UP OSD via SRX-PRO SERVER v6
and lower
1.
Repeat Steps 1-8 of the ADJUST ZOOM/FOCUS via SRX-
PRO SERVER v6 and lower section.
2.
Use the
Iris Open
and
UP/DOWN/LEFT/RIGHT
buttons on the Advanced Control
panel to bring up and navigate in the OSD menus.
LENS ADJUSTMENT
Your Am57 camera is equipped with the motorized 2.7-13.5mm lens. To achieve
desired view, start by adjusting the lens angle along the 3 axis by panning/tilting the
camera body and rotating the lens assembly. The lens zoom and focus can be adjusted
through i3’s encoder, i3’s standalone HVR’s local or remote interfaces, through SRX-
Pro v6/VPC interface, or through HD service monitor with BNC input.
ADJUST ZOOM/FOCUS via HR16/HR16v2
1. Connect Am57 to HR16/HR16v2.
2.
In Internet Explorer, enter HR16/HR16v2 address. (Default: 192.0.0.16).
3. Enter user credentials in the Annexxus login screen.
(Default: i3admin/i3admin or i3admin/i3admin1).
4. Go to SETUP > Camera > PTZ Settings
5.
In
Channel No.
, select the HR16/HR16v2 port
where Am57 is connected (E.g. Analog Camera 1).
6.
In
PTZ Protocol
, select
i3-HDA
. Click
Save
.
7. Click LIVE to go back to the live mode. Select a
single camera division.
8. Use Previous/Next buttons to locate desired
Am57 camera.
9. Use the PTZ Control panel to adjust Zoom and
Focus until the desired view is achieved.
ADJUST ZOOM/FOCUS via SRX-PRO
SERVER v6 and lower
1.
Repeat Steps 1-6 of the ADJUST ZOOM/FOCUS via HR16/HR16v2 section.
2. Add HR16/HR16v2 to SRX-Pro Server’s IP camera tab.
3.
In IP Camera tab, expand HR16/HR16v2 item to see all inputs. Assign Am57
input to SRX-Pro Server video channel in Ch. In. drop-down menu.
4.
Go to Hardware > Channels setup tab.
5. Locate the Channel that Am57 was assigned to in
the Step 3 and set
PTZ Camera Type
to
i3 GiPi
.
6. Click the Live Mode button.
7.
Go to
View > Tree View
and expand Advanced
Control panel.
8.
Double-click on the Am57 camera to bring it into
full single-channel division.
9.
Use the Advanced Control panel to adjust Zoom
and Focus until the desired view is achieved.
ADDING HR16/HR16v2 to SRX-PRO v7 (and up)
SRX-Pro v7 users must complete this step before adjusting
lens zoom/focus through VPC.
1. Repeat Steps 1-6 of the ADJUST ZOOM/FOCUS via
HR16/HR16v2 section.
2. Log into Pro Setup
3. Click Add.
4. Select one or more HR16/HR16v2 inputs.
Note: In SRX-Pro v.7.1, HR16/HR16v2 will be automatically discovered and
displayed under UNASSIGNED CAMERAS. You may need to click REFRESH .
In SRX-Pro v.7.2 and up, click SEARCH and wait
until your encoder is discovered.
5. Click ADD.
6. Click List.
7. Enable PTZ toggle for all Am57 inputs on HR16/HR16v2.
3
4
5
6
7