User Manual
Thank you for purchasing i3 International’s Am53 High Definition indoor/outdoor analog
dome camera. Your camera is equipped with a motorized vari-focal 2.7-13.5mm @ F1.2
lens. The lens can be controlled through IE interface of the i3 encoders/standalone DVRs, or
through SRX-Pro Server/VPC using camera’s built-in OSD menu.
SAFETY
When installing your Am53 camera be sure to avoid:
• excessive heat, such as direct sunlight or heating appliances
• contaminants such as dust and smoke
• strong magnetic fields
• moisture and humidity
• areas with mechanical vibrations
• fluorescent lamps or objects that reflect light and unstable light sources
• temperatures below -40°C (-40°F) and above 50°C (122°F)
POWER
This camera accepts DC12V and AC24V power.
Maximum power consumption: 9.7W.
Ensure the supplied voltage meets the power consumption requirements of this camera
before powering the camera on. Incorrect voltage may cause irreparable damage to the
video camera and will effectively void the camera warranty.
CLEANING & SERVICING
For maximum optical clarity, the camera dome or lens must remain clean. Use a soft, dry
cloth to remove finger prints or dust from the dome cover.
• Use a blower to remove dust from the lens.
• Do not use volatile solvents such as alcohol, benzene, or thinners, as they may
damage the surface finishes.
• To avoid electrical shock and to preserve the product warranty, DO NOT disassemble
the camera. Refer servicing to qualified personnel only.
PACKAGE CONTENTS
Ensure that the items received match those listed on the order form and the packing slip.
In addition to this manual and a fully assembled camera, the dome camera packing box
includes:
A.
Plastic Anchor x3
B.
Round Head Screw
(Tapping Type) x3
C.
Waterproof tape x1
D.
Security Torx bit
E.
Service Monitor BNC cable x1
F.
Surface Mount template x1
1.
Cable exit plug. Use a coin or a flat screwdriver to turn counter-clockwise to
remove.
2.
Camera cable. When surface mounting, route through the cable exit opening.
3.
Camera module/lens.
4.
Dome bubble.
5.
BNC video connector. Connect to an encoder, DVR/HVR or service monitor.
Four (4) video formats supported: HD-TVI (
default
), HD-AHD, HD-CVI and CVBS.
Use the video format switch (#2) to set video format as required.
6.
Power connector (DC12V/AC24V).
7.
Video format switch. Default video format setting: HD-TVI.
DISASSEMBLY AND INSTALLATION
To prepare the camera for mounting, remove the camera’s dome bubble by unscrewing
three screws using the Security torx bit provided. Do not remove the screws completely.
The dome bubble is secured to the camera body with the anti-drop wire.
Lift the dome bubble off.
Prepare the mounting surface:
• Depending on the type of
installation, additional mounting
accessories may need to be
purchased.
• It is the installer’s responsibility
to ensure that the mounting
surface is suitable for the
chosen installation method.
• Based on installation location
and surface type, supplied
screws and anchors may not be adequate. Mounting hardware is site-specific and
may need to be supplied by the installer.
Compatible i3 Mounting Accessories:
B5
- Pendant mount back box / bracket. 1” Male. Combine with DB61 for Wall mount
installations
DB61
- Wall Mount bracket. 1” Female. Combine with B5 for Wall Mount installations.
DIMENSIONS AND DEFINITIONS
1080P (2MP) Outdoor IR HD Analog Dome w/ Motorized Lens
Am53
HD
3
4
5
6
7
A
B
F
Waterproof tape
e Waterproof tape
pe Waterproof ta
f tape Waterproo
oof tape Waterpr
proof tape Water
C
D
111mm (4.4”)
Ø146mm (5.7”)
Ø99.94mm (3.93”)
Ø130mm (5.11”)
3x Ø4.6mm
(0.18”)
HIGH DEFINITION ANALOG VIDEO SUPPORT
Your Am53 camera supports the standard CVBS composite analog video stream (720x480)
and a high-definition (2MP) video stream in HD-TVI, HD-AHD, and HD-CVI format.
Note: Am53 camera supports a single video output at-a-time. No separate spot monitor
output is offered.
IMPORTANT:
In order to use high-definition video, your Am53 camera
must be
connected to a video encoder
or standalone DVR/HVR that supports HD-TVI,
HD-AHD, or HD-CVI format.
Note:
i3’s line of encoders and embedded standalone DVRs supports HD-TVI and CVBS
formats only.
CHANGING VIDEO FORMAT:
- Unscrew protection cap from the video format switch (#7 under Dimensions
and Definitions section).
- Press and hold the button for 5 seconds to change the video output format to
the next one in sequence.
Video format sequence:
TVI (default) > AHD > CVI > CVBS.
1
2
E
