USER MANUAL
Page -2-
Am53 Analog Dome Camera
LENS ADJUSTMENT
Your Am53 camera is equipped with the motorized 2.7-13.5mm lens. To achieve
desired view, start by adjusting the lens angle along the 3 axis by panning/tilting the
camera body and rotating the lens assembly. The lens zoom and focus can be adjusted
through i3’s encoder, i3’s standalone HVR’s local or remote interfaces, through SRX-Pro
v6/VPC interface, or through HD service monitor with BNC input.
ADJUST ZOOM/FOCUS via HR16
1.
Connect Am53 to HR16.
2.
In Internet Explorer, enter HR16 address. (Default: 192.0.0.16).
3.
Enter user credentials in the Annexxus login screen.
(Default: i3admin/i3admin).
4.
Go to
SETUP > Camera > PTZ Settings
5.
In
Channel No.
, select the HR16 port where Am53 is connected (E.g.
Analog Camera 1).
6.
In
PTZ Protocol
, select
i3-HDA
. Click
Save
.
7.
Click
LIVE
to go back to the live mode. Select a single camera
division.
8.
Use Previous/Next buttons to locate desired
Am53 camera.
9.
Use the PTZ Control panel to adjust Zoom and
Focus until the desired view is achieved.
ADJUST ZOOM/FOCUS via SRX-PRO
SERVER v6 and lower
1.
Repeat Steps 1-6 of the
ADJUST ZOOM/FOCUS via HR16 section.
2.
Add HR16 to SRX-Pro Server’s IP camera tab.
3.
In IP Camera tab, expand HR16 item to see all inputs. Assign Am53 input to SRX-
Pro Server video channel in
Ch. In.
drop-down menu.
SURFACE MOUNTING
1.
Attach the supplied surface mounting template to the mounting surface.
2.
Drill three mounting holes in the surface and insert supplied anchors.
3.
Drill the conduit hole for the camera cable, as marked on the template (if applicable).
If routing the cable through the side cable exit, do not drill the cable exit hole, instead
remove the cable exit plug. If mounting on a wall, make sure the opening is pointing
down, to create a drip loop.
4.
Use the tapping screws provided (if suitable for the installation) to secure the camera
to the prepared mounting surface.
5.
Feed the camera cables through the conduit hole.
6.
Connect camera’s BNC connector to the coaxial cable.
7.
Connect camera to DC12V/AC24V power, 9.7W required.
8.
Adjust the lens angle by panning and tilting the camera lens assembly and rotating
the camera lens base. Do not over-rotate beyond the stop point to avoid damage to
the camera.
9.
Adjust the camera’s zoom and focus through a DVR/HVR, encoder, SRX-Pro/VPC
software or HD service monitor with BNC input.
See LENS ADJUSTMENT section for more information.
10.
Adjust any additional camera settings (e.g. image brightness, color or contrast, day/
night mode, etc.).
See CAMERA MENU section for more information on camera’s
on-screen menu.
11.
Once the desired view is achieved, re-attach the camera’s dome bubble onto the
camera module using the security torx bit provided.
4.
Go to Hardware > Channels setup tab.
5.
Locate the Channel that Am53 was assigned to in the Step
3 and set
PTZ Camera Type
to
i3 GiPi
.
6.
Click the Live Mode button.
7.
Go to
View > Tree View
and expand Advanced Control
panel.
8.
Double-click on the Am53 camera to bring it into full
single-channel division.
9.
Use the Advanced Control panel to adjust Zoom and
Focus until the desired view is achieved.
3-axis Range Limitations:
Pan:
0-355°
Tilt:
0-75°
Rotation:
0-355°
PENDANT MOUNTING
(Optional B5 back box required)
1.
Attach B5 back box to the 1” pendant mounted pipe or pipe bracket.
To attach to 3/4” pipe, use a 1” to 3/4” reducer (not provided).
2.
Follow DISASSEMBLY instructions to lift off camera’s dome bubble.
3.
Complete Steps #6-7 in the
SURFACE MOUNTING section.
4.
Feed the camera cables into the B5 back box through the cable opening.
5.
Use three machine type screws provided with B5 to secure the Am53 camera to the
B5 backbox through the three mounting holes on the camera body.
6.
Complete Steps #8-11 in the
SURFACE MOUNTING section.
WALL MOUNTING
(Optional DB61 gooseneck bracket and B5 back box required)
1.
Mount DB61 gooseneck bracket on the wall. Follow installation instructions provided
with DB61.
2.
Attach B5 back box to the DB61 gooseneck bracket.
3.
Complete Steps #2-6 in the PENDANT MOUNTING section.
ADDING HR16 to SRX-PRO SERVER v7 and up
SRX-Pro v7 users must complete this step before adjusting lens
zoom/focus through VPC v7 and above.
1.
Repeat Steps 1-6 of the
ADJUST ZOOM/FOCUS via HR16 section.
2.
Log into Pro Setup
3.
Add HR16
i.
Click
Add.
ii.
Select HR16 in the list.
iii.
Click
ADD.
iv.
Click
List
and enable
PTZ
toggle for all Am53 inputs on HR16.
i
ii
iii
iv
