Midwest | 05
www.iboxstyle.com
1.
Turntable platter
2.
Spindle
3.
45 RPM Spindle Adaptor
4.
Folding tone arm standby clip
5.
Tone arm rest
6.
Tone arm
7.
BT status LED
8.
BT speaker On/Off
9.
BT speaker Pause/Play (short press), Disconnect/
Connect (long press)
10.
(long press),
Next track (short press, BT only)
11.
Volume - (long press), Previous track (short press,
BT only)
12.
Cartridge with stylus
13.
3.5mm Aux in socket
14.
Mode LED (Red=Phono/
Purple=Aux/Blue=Bluetooth)
15.
Mode selector switch
16.
Speed selector switch (331/3, 45, 78rpm)
17.
Magnetic socket
18.
Headphone socket
19.
Micro USB charging socket for BT speaker
20.
Magnetic plug
21.
Auto stop On/Off button
22.
RCA/Phono line-out L/R
23.
DC in power socket
Controls & Features
1. Remove the unit from all packaging and place on
a stable level surface, then remove any tape or
wire holding parts of the turntable in position.
2. Plug the jack plug from the power adaptor
supplied into the DC IN socket (23) on the back of
the turntable housing then plug the power
adaptor into a three pin mains socket and switch
the socket on. The adaptor will power the
turntable and also charge the BT speaker at
the same time.
3. Remove the protective Stylus Guard from the
tone arm cartridge (12) by gently pulling it
forwards.
4. Lift the tone arm (6) and fold down the standby
clip (4).
5. Place the tone arm (6) on the tone arm rest (5).
6. Turn the mode selector switch (15) to the PHONO
position (the mode LED (14) will light up Red).
7. Adjust the volume to a low/mid level using the
/- buttons (10 & 11).
8. Carefully place a record/disc on the platter/
turntable (1).
9. Turn the Speed selector switch (16) to the correct
speed (33, 45 or 78 rpm) for the disc you want to
play.
10. Make sure the Auto stop button (21) is in the On
position.
11. Lift the tone arm (6) and place the stylus at the
start of the record, the turntable will start
spinning automatically, gently lower the tone arm.
12. Adjust the volume to your preferred level using
the /- buttons (9&10).
13. When the disc has finished playing the turntable
will stop turning automatically, lift the tone arm
and return it to the tone arm rest (5).
14. To stop manually lift the tone arm and return it to
the tone arm rest (5). The turntable will stop
turning automatically. If you want to stop the
turntable without moving the tone arm turn the
mode selector switch (15) to the OFF position.
Setting up and operating your turntable
PLEASE NOTE:
When you are not using the turntable to play vinyl records we recommend you replace the stylus
cover and unfold the tone arm standby clip (4) and clip the tone arm to it to protect the stylus and tone arm.
Some records may have an auto-stop area outside
the pre-set limit, so the turntable stops before the
last track finishes. If this happens, set the AUTO-
STOP switch (21) to the OFF position. This will allow
the record to play to the end, but please note that it
will not stop automatically. You must manually raise
the tone arm and place it back in the rest and then
turn the AUTO-STOP switch (21) back ON to stop the
turntable from spinning.
Auto-Stop switch operation
Some 45rpm records may have had their centres
pressed out for playing on a juke box. Place the
adaptor on the spindle to play these records.
Spindle adaptor
