Genuine Accessories
Electronic Installation Instructions
Glasses
Gloves
Mask
Hearing Protection
Part Weight (Gross)
FMVSS 110 Compliance Information
Technical Support
1)
Read the entire Installation Instructions prior to beginning the installation of the part.
2)
3) Make sure the vehicle is completely clean and dry in the area(s) the part is to be installed.
4) Ensure the vehicle is properly protected in the area(s) that the accessory is to be installed.
5) NEVER place tools on painted surfaces, seating surfaces, dash pad, console or floor carpet/mats.
6) Always wear appropriate personal protective equipment, including gloves, safety glasses, etc., when required.
7) Record radio presets prior to disconnecting battery power, if needed.
8) Roll down the driver's window and adjust the power seats (if applicable) prior to disconnecting battery power, if needed.
9)
To prevent stress on the remote start wire harness, ensure the tilt steering column is fully extended before installing the kit.
10)
Ensure Transportation Switch is switched to 'ON' on the fuse box.
11)
Vehicle should be at room temperature.
12)
Language
English
6/5/2020
Rev. Date
Accessory:
Vehicle Model:
Difficulty stated above reflects the minimum level of
expertise required to install the accessory:
( B )
Remote Engine Start - Key Start
(A) Customer
Venue
Difficulty:
Part No.
Model Year
Copy OEM Logo Here (
→
)
2020~
K2F57 AC000
Note:
(B) Dealer Technician
Instructional Symbols / Definitions
Application Notes
Denotes quality processes to be checked
prior to moving to the next step
Denotes personal protective equipment (PPEs) that
may be required for a step. Examples of safety
equipment icons noted below:
Denotes cautions to be taken to avoid
vehicle and component damage
Ratchet
12mm Socket
10mm Socket
Extension
Basic Required Tools
Vehicle must be equipped with mechanical key start.
Ensure vehicle does NOT have SMART KEY (PUSH BUTTON IGNITION SYSTEM).
Vehicle should be equipped with automatic transmission, power door locks, and power windows. If these features are not equipped on the vehicle, do not proceed with install.
Denotes warnings that may lead to
serious physical injury or vehicle damage
#2 Phillips
Screwdriver
(C) Master Technician or Specialist
Authorized dealers use:
Hours:
Clip Removal Tool
Trim Removal Tool
Clean Cloth
50/50 Isopropyl
Alcohol (70%) and
Water Mix
N
O
T
E
Denotes important information to be
reviewed during the step
Denotes specific tools that are necessary
to complete a step
Notes to the installer:
Pliers
(1) 855-225-7344
M~F - 9am~5pm Pacific Standard Time
If this is a printed copy of the installation instructions, ensure you have the latest revision by
scanning the QR code or by entering the website address listed below before beginning
installation. Use the latest revision date as noted by “Rev. Date” above.
www.hyundaiaccessories.com/admin_media_uploads/installationSheets/k2f57_ac000.pdf
1.32
lbs
All dealers must determine if the Net weight they have added in the form of all options or accessories, when added to the weight of all Port/Dealer
Installed options or accessories, exceeds the lesser of 1.5% of GVWR or 100 lbs. If the additional weight does exceed the lesser of the indicated
thresholds, a “Load Carrying Capacity Reduced” label must be installed. A black, fine-point, indelible marker must be used to write by hand onto the
label, the reduced carrying capacity in kilograms or pounds, which is the total weight of all added options and accessories.
Load Label Part Number: NP070 - 09003
0.60
kg
If applicable, scan the barcode label located on the accessory part or packaging prior to installing, to register the part. If this accessory is installed as
a replacement, register the removal of the old part before registering the new part. Old and new parts will have different barcode data, and the old
registration cannot be reused.
Denotes cautions to be taken to avoid
physical injury or electronic component
damage
The order of the disassembly and reassembly steps have been optimized for maximum efficiency and the correct installation of the Remote Engine Start
kit. Disassemble vehicle components (including harness connectors) and install the kit components according to each step, as indicated. Avoid
disassembling or reassembling any components in advance to prevent unnecessary labor time and/or installation errors.
Torque Wrench
Wire Cutters
Revision Date
06/05/2020
Page 1 of 13
