background image

Genuine Accessories

 

 

Clean Cloth and 50/50 Mix of Isopropyl Alcohol (70%) and Water

12

N
O
T
E

GO TO → Function Check

A. Perform the Function Check at the end of the Instructions.        

13

#2 Phillips Screwdriver

N
O
T
E

A. Reinstall all removed parts as follows:
    - Install the Remote Start OBDII Connector to the Lower Dash Panel.
    - Install the Lower Dash Panel ensuring the Lower Tab on the left hand
      side bottom of panel is first tucked into the Kick Panel.
    - Reinstall the Dash End Cap.
    - Reinstall the Weatherstrip ensuring there are no kinks.
    - Reinstall Fuse Panel Cover.
B. Place the Quick Reference Guide and the Owner’s Guide into the Glove 
    Box.
C. Attach the Remote Start Fobs to each of the Factory Key Fob Rings.

N
O
T
E

N
O
T
E

A. Reconnect the Negative (-) Battery Cable. Torque to:
    

5.0 ~ 6.0 N.m (0.5 ~ 0.6 kgf.m, 45 ~ 52 lb-in)

B. Reinstall the vehicle's Negative (-) Battery Terminal Cover, if applicable.
C. Make sure the Transportation Fuse is in the "ON" position.
D. Reinstall the weatherstrip at dash area to allow Driver's Door to
    close properly.
E. Close the Hood, Tailgate and all Doors.
F. Test the LOCK / UNLOCK function using Smart Key Fob.
G. Enter the vehicle, holding a Smart Key, depress the Brake Pedal and
    push the START button to start the engine.
H. Wait for 5 sec., and push the START button to stop the engine.

Ensure the surface is completely dry before installing the Warning Label.
Ensure the label is aligned straight with the edge of the Radiator Cover 
and without air bubbles under the label.

NOTE:  If vehicle is not responding, carefully re-check all wiring 
connections.  If the vehicle is still not responding, follow the 
Troubleshooting at the end of the instructions.

10

11

Ratchet, 10mm Deep Well Socket, Extension, and Torque 
Wrench

A. Clean the left top surface of the Radiator Cover.
  - Ensure the surface is completely dry.
B. Remove the Adhesive Liner from the Warning Label, then secure
    the label to the Radiator Cover as shown.

Warning Label 

Negative Battery  

Cable 

Negative Battery  

Cover 

Revision Date

01/02/2019

Page 7 of 10

Summary of Contents for J9F57 AC200











Reviews: