Genuine Accessories
Electronic Installation Instructions
Glasses
Gloves
Mask
Hearing Protection
Part Weight (Gross)
FMVSS 110 Compliance Information
Technical Support
1) Read the entire Installation Instructions prior to beginning the installation of the part.
2) Make sure the vehicle is completely clean and dry in the area(s) the part is to be installed.
3) Ensure the vehicle is properly protected in the area(s) that the accessory is to be installed.
4) NEVER place tools on painted surfaces, seating surfaces, dash pad, console or floor carpet/mats.
5) Always wear appropriate personal protective equipment, including gloves, safety glasses, etc., when required.
6) Record radio presets prior to disconnecting battery power, if needed.
7) Ensure the transportation fuse is set to "ON" before starting the install, if applicable.
8) Roll down the driver's window and adjust the power seats (if applicable) prior to disconnecting battery power, if needed.
9) Vehicle should be at room temperature.
10)
(B) Dealer Technician
Instructional Symbols / Definitions
M~F - 9am~5pm Pacific Standard Time
Hours:
50/50 Isopropyl
Alcohol (70%) and
Water Mix
Notes to the installer:
10mm Deep Well
Socket
Torque Wrench
Trim Removal Tool
Wire Cutters
Clean Cloth
Application Notes
Language
English
1/2/2019
Rev. Date
Accessory:
Vehicle Model:
Difficulty stated above reflects the minimum level of
expertise required to install the accessory:
( B )
Remote Engine Start - Push Start
(A) Customer
Kona
Difficulty:
Part No.
Model Year
Copy OEM Logo Here (
→)
2018~
J9F57 AC200
Note:
Denotes cautions to be taken to avoid
vehicle and component damage
Ratchet
Extension
Authorized dealers use:
Denotes specific tools that are necessary
to complete a step
#2 Phillips
Screwdriver
Denotes cautions to be taken to avoid
physical injury or electronic component
damage
0.53
Basic Required Tools
Vehicle must be equipped with Smart Key (Push Button Start).
Ensure vehicle does NOT have Mechanical KEY.
Vehicle should be equipped with automatic transmission, power door locks, and power windows. If these features are not equipped on the vehicle, do not proceed with install.
(1) 855-225-7344
Denotes warnings that may lead to serious
physical injury or vehicle damage
N
O
T
E
Denotes important information to be
reviewed during the step
Denotes quality processes to be checked
prior to moving to the next step
Denotes personal protective equipment (PPEs) that
may be required for a step. Examples of safety
equipment icons noted below:
lbs
All dealers must determine if the Net weight they have added in the form of all options or accessories, when added to the weight of all Port/Dealer Installed
options or accessories, exceeds the lesser of 1.5% of GVWR or 100 lbs. If the additional weight does exceed the lesser of the indicated thresholds, a “Load
Carrying Capacity Reduced” label must be installed. A black, fine-point, indelible marker must be used to write by hand onto the label, the reduced carrying
capacity in kilograms or pounds, which is the total weight of all added options and accessories.
Load Label Part Number: NP070 - 09003
0.24
kg
The order of the disassembly and reassembly steps have been optimized for maximum efficiency and the correct installation of the
Remote Engine Start kit. Disassemble vehicle components (including harness connectors) and install the kit components according to
each step, as indicated. Avoid disassembling or reassembling any components in advance to prevent unnecessary labor time and/or
installation errors.
(C) Master Technician or Specialist
Entered by
MPA
If this is a printed copy of the installation instructions, ensure you have the latest revision by
scanning the QR code or by entering the website address listed below before beginning
installation. Use the latest revision date as noted by “Rev. Date” above.
www.hyundaiaccessories.com/admin_media_uploads/installationSheets/j9f57_ac200.pdf
Revision Date
01/02/2019
Page 1 of 10
